Self-Priming From Open Tanks/Containers And Natural Water Sources; Bleeding The Appliance; Use; Filling Oil/Petrol - Parkside PHDB 4 B2 Traducción Del Manual De Instrucciones Original

Self-priming from open tanks/containers and
natural water sources
Use the self-priming equipment supplied.
–
Intake filter
–
3 m reinforced suction hose
With this accessory the appliance can draw water to max. 1 m above the
water surface. This can take up to 1 minute.
♦ Immerse the 3 m suction hose
out.
♦ Connect the suction hose
intake filter remains underwater.
♦ Run the appliance without the hand spray gun
flows evenly out of the high-pressure hose
If no water flows out after 1 minute, switch the appliance off and
check the appliance. Once the water flows, switch off the appliance
and attach the hand spray gun
work.
■ It is important that the hose and coupling are of a good quality, tightly
fitted and that the seals are undamaged and inserted straight. Leaky
connections can impair the suction.

Bleeding the appliance

♦ Remove the nozzle .
♦ Start the engine (see "Starting the engine").
♦ Pull the trigger on the hand spray gun
♦ Allow the appliance to run until the water comes out of the jet pipe
without any air bubbles.
♦ Switch off the appliance and screw the nozzle
│ GB │ IE
■ 30
completely underwater to get the air
to the appliance and ensure that the
attached until water
.
and the jet pipe so you can
several times.
back on.

Use

WARNING!
► Switch off the appliance before making any adjustments or carrying
out maintenance work.
DANGER! RISK OF EXPLOSION! DO NOT SPRAY
FLAMMABLE LIQUIDS!
► Place the appliance on a firm surface.
► The high-pressure cleaner may not be operated by children.
(Risk of accidents due to improper use of the appliance).
► The appliance generates a lot of noise.
Risk of hearing damage. Always wear suitable hearing protect when
working with the appliance.
► The water jet coming out of the high-pressure nozzle exerts recoil
force on the gun. An angled jet pipe can also cause torque.
Therefore, hold the jet pipe and gun firmly in your hands.
► Never aim the water jet at people, animals, the appliance itself or
electrical components.
► Vehicle tyres/tyre valves may only be cleaned at a minimum spray
distance of 30 cm. Otherwise the vehicle tyres/tyre valves could
be damaged by the high-pressure jet. The first sign of damage is a
discolouration of the tyre. Damaged vehicle tyres are a source of
danger.
► Materials containing asbestos or other substances that are harmful to
health may not be sprayed.
► To protect the operator from water spray, wear suitable protective
clothing.
► Always ensure that all hose connection are screwed tight.
► The trigger of the hand spray gun must not be jammed during use.

Filling oil/petrol

♦ When you use the appliance for the first time, unscrew the red oil inlet
screw and add approx. 0.6 l engine oil (15W40). Use the funnel
to do this.
♦ Unscrew the filler cap and add standard commercial lead-free
petrol to the fuel tank . The tank has a maximum capacity of 3.6 l.
Add fuel up to the red mark.

Starting the engine

CAUTION!
► Before first use, add engine oil (15W40, approx. 0.6 l) and fuel
(regular unleaded petrol).
♦ Check the fuel and oil levels; top up as necessary.
♦ Provide adequate ventilation for the appliance.
♦ Ensure that the spark plug/spark plug connector
CAUTION!
► When starting using the pull starter
can cause injuries to your hand.
■ Wear protective gloves when starting.
♦ Open the fuel tap ; to do this, move the fuel tap
position.
♦ Move the On/Off switch
to position I \ I (in the left position).
♦ Set the choke
are firmly fitted.
there can be a kickback that
to the "ON"
to the "ON" position.
PHDB 4 B2