BLACK&DECKER HT500 Manual De Instrucciones página 12

12 • ENGLISH
c. Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Black & Decker Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by Black &
Decker, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Hz ....... Hertz
Read
Instructions
W ........ Watts
Manual
min ..... minutes
Use Eye
Protection
..... Alternating
Current
Use Ear
Protection
..... Direct
Current
V ........ Volts
n ....... No-Load
0
Speed
A ........ Amperes
All manuals and user guides at all-guides.com
FEATURES (Fig. A)
1. Trigger switch
2. Front handle switch
3. Front handle
4. Guard
5. Blade
6. Blade sheath
7. Cable restraint
f Wear safety glasses or goggles when operating this
f Wear gloves when operating this tool.
f Wear ear protection when operating this tool.
f Immediately disconnect the cable from the mains if it
f Do not expose the tool to rain or high humidity.
f Keep the cable away from the blades while using
f If you have not used a hedgetrimmer before,
f Never touch the blades while the tool is running.
f Never attempt to force the blades to come to a
f Do not put the tool down until the blades have come
f Regularly check the blades for damage and wear.
f Take care to avoid hard objects (e.g. metal wire,
f Should the tool start to vibrate abnormally,
f If the tool stalls, immediately switch it off. Unplug the
f After use, place the blade sheath supplied over the
f Store the tool, making sure that the blade is not
...... Class II
Construction
.... Earthing
f Always ensure that all handles and guards are
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
f Never allow children to use the tool.
cation per
f Be aware of falling debris when cutting the higher
minute
f This appliance is not intended for use by young or
ADDITIONAL SAFETY INSTRUCTIONS
FOR HEDGETRIMMERS
tool.
is damaged or cut.
this tool.
preferably seek practical instruction by an
experienced user in addition to studying this manual.
standstill.
to a complete standstill.
Do not use the tool when the blades are worn or
damaged.
railings) when trimming. Should you accidentally
hit any such object, immediately switch the tool off,
unplug it and check for any damage.
immediately switch it off and check for any damage.
tool before attempting to remove any obstructions.
blades.
exposed.
fitted when using the tool. Never attempt to use
an incomplete tool or a tool with unauthorised
modifications.
sides of a hedge.
infirm persons without supervision. Children must
be supervised to ensure they do not play with the
appliance.