Tabla de contenido
Publicidad
PARAMETER
RANGE
Do this first
*****
290
0-9
002
0-254 st
004
0-254 st
005
0-254 st
009
On/Off
013
On/Off
023
0-1
100
0-254 st
110
70-390 rpm
111
200-9900 rpm
113
200-9900 rpm
114
200-9900 rpm
115
70-1500 rpm
117
400-9900 rpm
118
400-9900 rpm
128
0-2000 ms
129
0-3
130
On/Off
133
On/Off
134
On/Off
137
On/Off
161
0-1
202
0-500 ms
207
208
240
13
241
26
263
1
264
1
265
0-2550 ms
270
0-5
272
020-255
281
0-2550 ms
436
Front panel LED's:
LED 1: Off
LED 2: Off
LED 3: Off
LED 4: On
LED 5: Off
LED 6: On
LED 7: Off
LED 8: On
Stepper Speed Settings:
speed 1 (sewing): 118
speed 2 (chaining): 140
REV 2
211M Parameter Settings (TE Cut only)
VALUE
****
Perform a master reset before programming, see below
05
Mode of operation. MUST SET THIS PARAMETER FIRST!
033
020
001
Number of stitches for end of seam filtering.
On
Automatic cycle of machine from sew sensor.
On
Enabling of chain cutter.
1
Raising of presser foot at end of chain cut.
000
Softstart duration of sew head.
020
Positioning speed.
500 (5000) Maximum speed when "129" is 0, 1, or 2.
500 (5000) Speed setting for chaining duration.
500 (5000) Speed setting for end of sewing delay.
007 (70)
Speed setting for softstart duration.
500 (5000) Speed setting for folder blowers.
500 (5000) Maximum speed when "129" is 3.
040
Presser foot down delay from sew sensor covered.
Automatic start mode. 0=start & run with foot pedal only, no sensor; 1=run with pedal
speed control and sensor (end of cycle at pedal speed); 2= run with pedal speed control
2
and sensor (end of cycle at full speed); 3=fully automatic mode using sensor only (pedal is
locked out). Note: If E-Stop switch is up, unit is fully automatic with a setting of 2.
Off
Enabling of end of seam filtering.
On
Enabling of autotrim at end of cycle.
Off
Enabling of softstart.
On
Enabling of folder blowers.
0=cw/1=ccw Motor rotation
300
Sew head on delay from presser foot down.
55
Low speed braking.
55
High speed braking.
13
Enables folder blower sensor.
26
Enables stacker sensor.
1
Inverts logic of folder blower output.
1
Inverts logic of stacker output.
040
Stacker door on duration.
2
External handwheel sensor configuration.
Drive ratio between motor pulley and handwheel pulley. If handwheel pulley is smaller than
motor pulley, increase this value to slow down sewing head until measured speed
100
matches speed set with parameter 111. (For Yamato and Pegasus, setting should be
100; for Rimoldi, setting should be 124)
005 (50)
Duration of chain cutter.
0
Use code "5913". This disables an input that was causing box to reset itself.
Programming Instructions:
1. Power on holding down the "P" button till "COD" is displayed.
2. Press ">>" once and enter the number "311"
3. Press "E" once and "2.0.0." is displayed this is a parameter
4. Proceed to the parameter to be changed and press "E".
5. The value now shows in the screen, adjust to desired value.
6. Press "E" to enter value and continue with parameter setting.
7. Repeat for other parameters, press "P" once when complete.
8. Run sewing head to save parameters before powering down
To Perform Master Reset of Parameters:
1. Power on holding down the "P" button till "COD" is displayed.
2. Press ">>" once and enter the number "591"
3. Press "E" twice and "093" is displayed.
4. Press "+" once, "094" is displayed.
5. Press "P" to exit programming mode with all default values.
DESCRIPTION
Duration of puller in chaining speed.
Delay before puller changes to chaining speed.
Technical Manual & Parts Lists
18
Publicidad
Tabla de contenido
