EAS ELECTRIC 52 Manual De Usuario página 141

How To Use The Advanced Functions
ECO function
NOTE: This function is only available under
COOL mode.
Used to enter the energy efficient mode.
Under cooling mode, press this button,
the remote controller will adjust the
O
temperature automatically to 24 C, fan
speed of Auto to save energy(but only
O
if the set temperature is less than 24 C).
O
If the set temperature is above 24 C ,
press the ECO button, the fan speed
will change to Auto, the set temperature
will remain unchanged.
NOTE:
Pressing the ECO button, or modifying
the mode or adjusting the set temperature
O
to less than 24 C will stop ECO operation.
Under ECO operation, the set temper-
O
ature should be 24 C or more. it may
result in insufficient cooling. If you feel
uncomfortable, just press the ECO
button again to stop it.
SLEEP Function
The SLEEP function is used to decrease
,
energy use while you sleep (and don t
need the same temperature settings to
stay comfortable). This function can
only be activated via remote control.
, , ,,
For the detail, see sleep operation in
,
,,
, ,
USER S MANUAL.
Note: The SLEEP function is not
available in FAN or DRY mode.
Follow me function
The Follow me function enables the
remote control to measure the temperature
at its current location and send this signal
to the air conditioner every 3 minutes interval
When using AUTO, COOL, or HEAT modes,
measuring ambient temperature from the
remote control (instead of from the indoor
unit itself) will enable the air conditioner to
optimize the temperature around you and
ensure maximum comfort.
V.1
Silence function
Hold down Fan speed button for 2 seconds
to activate/cancel Silent mode. Due to low
frequency operation of compressor, it may result
in insufficient cooling and heating capacity.
(applicable to the air conditioner with Silent
feature only)
Hold down Fan
button for 2
seconds to activate
Silence function
MODE FAN
ON/OFF
Press this button
twice in one second
to activate 8 C
heating function
SWING
TIMER
Hold down this
SWING
LED FOLLOW
button for 2
ME
seconds to
SELF
SHORT activate sleep
TURBO
CLEAN
CUT
function
O
8 C Heating Function
When the air conditioner operates
under heating mode with the set
.
O
temperature of 17 C, press Temp
button twice in one second will
activate 8 Degree heating function.
The unit will operate at a setting
O
temperature of 8 C.
, ,
The indoor unit display shows FP .
13
How To Use The Advanced Functions
SWING function
SWING
Button
Used to stop or start vertical louver movement
and set the desired left/right air flow direction.
The vertical louver changes 6 degree in angle
for each press. If keep pushing more than 2
seconds, the vertical louver auto swing feature
is activated.
SWING
Button
Used to stop or start horizontal louver
movement or set the desired up/down air flow
direction. The louver changes 6 degree in
angle for each press. If keep pushing more
than 2 seconds, the louver will swing up and
down automatically.
SELF CLEAN function
Airborne bacteria can grow in the moisture
that condenses around heat exchanger in
the unit. With regular use, most of this
moisture is evaporated from the unit.
When the SELF CLEAN feature is activated,
O
your unit will clean itself automatically. After
that, the unit will turn off automatically.
You can use SELF CLEAN as often as you like.
Note: You can only activate this function
in COOL or DRY mode.
TURBO function
The TURBO function makes the unit work
extra hard to reach your present temperature
in the shortest amount of time possible.
When you select TURBO feature in COOL
mode, the unit will blow cool air with
strongest wind setting to jump-start the
cooling process.
When you select TURBO feature in HEAT
mode, for units with Electric heat elements,
the Electric Heater will activate and
jump-start the heating process.
LOCK function
Press Turbo button and Self clean
,,
button simultaneously for one second
to lock or unlock the keyboard.
MODE FAN
ON/OFF
SWING
TIMER
SLEEP
SWING
LED FOLLOW
ME
SELF
SHORT
TURBO
CLEAN
CUT
Hold together for one second
to activate LOCK function
SHORTCUT function
Used to restore the current settings or
resume previous settings.
Push this button when remote controller
is on, the system will automatically revert
back to the previous settings including
operating mode, setting temperature, fan
speed level and sleep feature (if activated).
If pushing more than 2 seconds, the
system will automatically restore the
current operation settings including
operating mode, setting temperature,
fan speed level and sleep feature
(if activated ).
14
V.1