Initial Start-Up - Martin Yale intimus 689 Instrucciones De Uso

GB
APPLICATION:
The document shredder INTIMUS 007SL / 007SF
is a machine for the destruction of common written
material.
CAUTION: The shredder should only
be fed with paper!
Shredding other data carriers can cause
injury(e.g. by splintering of hard materials)
or may damage the shredder (e.g.
destruction of the cutting system).
OPERATING FUNCTIONS:
1 = Rocker switch „ready" (fig. 1)
Depress this switch to start the machine or to
stop the machine.
2 = „Cutting system forward"
pushbutton (fig. 2)
Pressing this button starts the cutting system.
Material can now be fed to the shredder.
3 = „Cutting system stop"
pushbutton (fig. 2)
Pressing this button switches the shredder
off, thereby halting the cutting system.
4 = „Cutting system reverse"
pushbutton (fig. 2)
Pressing this button starts the cutting system
in reverse.
5 = Pilot lamp „ready" (fig. 2)
Lights when the rocker switch (1) is operated.
6 = Pilot lamp „collecting bag full" (fig. 2)
Lights as soon as the collecting bag is full and
needs to be emptied. At the same time the
machine switches off automatically.
7 = Pilot lamp „door open" (fig. 1)
Lights when the door is not closed. The
machine then switches off automatically and
it cannot be started as long as the door is
open.
8 = Light barrier (forward operation) (fig. 3)
The shredding operation is started as soon
as a sheet of paper passes through the feed
slot.
1
fig. 1
INITIAL START UP
INSTALLATION:
- Unpack and set machine upright.
- Put the collecting bag into the sliding frame (see
description „EMPTYING THE COLLECTING
BAG").
- Plug in the machine (for instructions for the
necessary precautions see „TECHNICAL
DATA".
OPERATION
OPERATING THE MACHINE:
To start, switch on the unit by operating the rocker
switch (1) (fig. 1).
The pilot lamp marked „ready for operation" (5), as
well as the red stop-button „S" (3) (fig. 2) will light
to indicate that the machine is ready for operation.
The paper tray may not be used as a
step ladder or as a seat. Danger of
tipping over!
FEEDING PAPER:
- Feed paper through the inlet guide to the cutting
system.
- Machine switches automatically to forward and
draws paper in.
- The machine switches off automatically after
shredding.
S
4 3
2 5
fig. 2
8
fig. 3
4
The air vents in the housing are
necessary for cooling and may not be
covered or closed!
The mains connection at the machine
must be freely accessible!
Only operate the machine in enclosed
rooms at temperatures between 10°C
and 25°C!
Never feed the shredder with a quantity
of paper exceeding the maximum
indicated in the technical details.
Should the machine be overfed, follow
the instructions under „AUTOMATIC
RESPONSE
OVERLOADING".
EMPTYING THE COLLECTING BAG (fig. 4):
When the collecting bag is full, the machine turns
off automatically and a horn sounds. The pilot
lamp (6) (fig. 2) lights up. Empty the collecting bag
as follows:
- Open the door and take out the sliding frame
with the collecting bag.
- The pilot lamp (7) (fig. 2) lights up. The horn
stops. The pilot lamp (6) goes off.
- Remove the full sack and dispose of contents.
- Put the empty bag from below through the
sliding frame and put the edges of the bag
approx. 10 cm over the frame outwardly.
- Move back the sliding frame with the collecting
bag and close door. The pilot lamp (7) goes off.
Note: The machine will only run with closed door!
6 7
IN CASE OF
fig. 4