Allmatic BIOS1 24V Manual Del Usuario página 38

WARNING - Do not use with sliding gates.
23. MECHANICAL RELAXATION Mr.E.
Function for the mechanical relaxation of the motor: it is useful on those motors that have the unlock for the manual movement which can remain
locked due to the pressure of the motor on the mechanical stop. When it arrives on the mechanical stop, opening or closing, the motor will do a short
inversion of Mr.E. x 50ms.
NOTE - with MP.r with function enabled (pressure of the motor in closed position), the mechanical relaxation is performed only on the first positioning
on the mechanical stop.
WARNING - Do not use with sliding gates.
24. RESTORE DEFAULT SETTINGS DE.F.
With the item of the menu de.f. it is possible to restore the default settings of the control unit. The reset will restore all the parameters of the base
and advanced menu, but doesn't modify the learnt strokes.
Move to de.f. then press and hold the "MENU" button until the display shows a number (for example 0), then release the button.
Select the used motor with the "UP" and "DOWN" buttons:
• 0: CUSTOM
• 1: KALOS XL
• 2: KALOS 70
• 3: KALOS 110
• 4: SIM
• 5: KALOS XL FAST
Press and hold the "MENU" button until the number stops blinking, then release the button. Press and hold the "MENU" button, the display will show
a count down d80,d79,...,d01 don't release the button until the display showns DoN.
NOTE - to know the type of the selected motor, move on the item menu de.f.: the display shows alternating the de.f. and the selected motor. If a
parameter changes (that depends on the motor type, see chapter 11), on the display will also appear the letter
25. VIEWING OF THE MEMORY POSITION FOR A SINGLE TRANSMITTER TR.S.
With the item of the menu tr.S. it is possible to view the memory location in which a transmitter is memorized.
To perform the function, move to tr.S. and then confirm by pressing the "MENU" button. Keep pressed the "MENU" button untill the display will show
SEE, then release the button.
At this point press a button of the memorized transmitter (it does not active any command). The display shows:
• the memory location for 2 seconds, if is memorized;
• the written not for 2 seconds, if is not memorized.
After 2 seconds the display returns to the screen SEE and it will be possible to perform this function with another transmitter.
To exit the function, press the "MENU" button. Otherwise, after 15 seconds without transmission, the control unit exits the function and shows the
written tout.
26. CANCELLATION OF A SINGLE TRANSMITTER TR.C.
With the item of the menu tr.C. it is possible to delete a single transmitter from the memory.
To perform the function, move to tr.C. and then confirm by pressing the "MENU" button. Keep pressed the "MENU" button untill the display will show
0, then release the button. Select the memory location of the transmitter. Press and hold the "MENU" button untill the display will show CLr, then
release the button.
To exit the function, press the "MENU" button. If the display shows the written ERR there are problems with the memory (for example empty position
or disconnected memory).
27. CANCELLING ALL THE TRANSMITTERS TR.F.
With the item of the menu tr.f. it is possible to erase all the transmitters learnt.
Move to tr.f., then keep pressed the "MENU" button until the display shows 0, then release the button. Press again and keep pressed the "MENU"
button, the display will show a count down d80,d79,...,d01 do not release the button until the display showns don.
28. BLUETOOTH SI.d.
Item of the menu needed for the first coupling between an Android device and the control unit. Refer to the Help of the Android application for the
connection procedure.
18/20
ITA ENG FRA ESP
c (for example c 1).
6-1622400 rev.03 07/09/2018