Sub-Zero ICB424 Instrucciones De Instalación página 25

Model ICBWS-30 Installation
Flush Inset Panel
Illustrations A–D provide panel offsets and reveals for
model ICBWS-30 in a flush inset application. Refer to the
chart below for reference to the illustrations.
For additional information on panel reveals, visit the speci-
fication library section of our website, subzerotrade.com.
Panel Offsets
MODEL ICBWS-30
Door / Grille Sides
Grille Top
Grille Bottom / Door Top
Door Bottom
TOP VIEW
CABINETRY
DOOR / DRAWER / GRILLE
BACKER
CABINETRY
SPACER
GRILLE
mm
FLUSH INSET PANEL
8
mm
13
mm
16
SIDE VIEW
mm
Illus. A Illus. B
DOOR /
DRAWER
8
GRILLE
mm
4
mm
13
mm
DOOR
2
mm
8
mm
SIDE VIEW
SIDE VIEW
Illus. C Illus. D
Dual Installations
When two models ICBWS-30 or a model ICBWS-30 and
built-in unit are installed side by side, a dual installation kit
may be required. Contact your Sub-Zero dealer for the
proper components and installation instructions.
DUAL STANDARD INSTALLATIONS
Illus.
Two overlay or stainless steel units may be placed side by
side in a dual installation. Some dual standard installations
A
will require a dual installation kit, available through your
B
Sub-Zero dealer.
C
A custom filler strip can be used in between two units in
D
an overlay or stainless steel design application. It is rec-
ommended that the filler strip be at least 51 mm wide, to
prevent condensation between the units. Be sure to add
the filler strip width to your rough opening width.
13 mm
Dual installations without a filler strip can only be accom-
plished using two units with opposite hinges as shown in
3
illustration A below. The dual installations shown in illus-
mm
8
trations B and C require a filler strip.
IMPORTANT NOTE: For the application shown in illustra-
tion A, a dual installation accessory kit is required.
WITHOUT FILLER STRIP FILLER STRIP REQUIRED
8
mm
2
mm
Illus. A Illus. B
DUAL FLUSH INSET INSTALLATIONS
Installing two models ICBWS-30 or a model ICBWS-30
and built-in unit side by side in a flush inset application will
require adjustments to the dimensions of your finished
rough opening, panel sizes and panel offsets. It will also
require a dual installation kit, available through your
Sub-Zero dealer.
Dual installations without a filler strip can only be accom-
plished using two units with opposite hinges as shown in
illustration A below. The dual installations shown in illustra-
tions B and C require a filler strip. Illustration A is the only
application that will accommodate the dual wide grille.
IMPORTANT NOTE: The application shown in illustration A
can only be achieved by installing dual flush inset panels.
Failure to install dual flush inset panels will cause the
handle side of the panels to collide when closing. In this
application a dual installation accessory kit is also
required.
Dual flush inset panels and dual installation kits are avail-
able through your Sub-Zero dealer. Refer to the illustration
and chart for dual flush inset panel specifications.
FILLER STRIP REQUIRED
Illus. C
subzero.com
Flush Inset Panels—Dual Installation
H
A
A A
H
A
W
Model ICBWS-30
DOOR W
Flush Inset Panel 775 mm
Spacer Panel 740 mm
Backer Panel 756 mm
GRILLE W
Flush Inset Panel 775 mm
Spacer Panel 740 mm
Backer Panel 756 mm
WINDOW W
Cut-Out 584 mm
Location
Grille panel dimensions listed are for a standard 2134 mm
overall height of the unit. For a 2108 mm overall height,
subtract 25 mm from grille panel height dimensions. For a
2235 mm overall height, add 102 mm to height dimensions.
Width dimensions do not vary.
25
H
1772 mm
1751 mm
1767 mm
H
235 mm
211 mm
227 mm
H
1581 mm
A
95 mm