Packing List - Ego Power+ BCX3800 Manual De Usuario

PREPARATION
EN
◾
Never operate this product while people, especially
children, or pets are nearby.
◾
Wear eye protection and stout shoes at all times while
operating this product.
◾
The distance between the machine and bystanders
shall be at least 15m.
OPERATION
◾
Use the brush cutter only in daylight or good artificial light.
◾
Never operate the brush cutter with damaged guards
or shields or without guards or shields in place.
◾
Switch on the motor only when the hands and feet are
away from the cutting means.
◾
Always disconnect the brush cutter from the power
supply (i.e. remove the battery pack).
◾
whenever leaving the brush cutter unattended;
◾
before clearing a blockage;
◾
before checking, cleaning or working on the brush cutter;
◾
after striking a foreign object;
◾
whenever the brush cutter starts vibrating abnormally.
◾
Take care against injury to feet and hands from the
cutting means.
◾
Always ensure that the ventilation openings are kept
clear of debris.
MAINTENANCE AND STORAGE
◾
Disconnect the brush cutter from the power supply
(i.e. remove the battery pack) before carrying out
maintenance or cleaning work.
◾
Use only the manufacturer's recommended replacement
parts and accessories.
◾
Inspect and maintain the brush cutter regularly. Have the
machine repaired only by an authorized repairer.
◾
When not in use, store the brush cutter out of the reach
of children.
OTHER SAFETY WARNINGS
◾
Avoid dangerous environments - Don't use
appliances on damp or wet slope.
◾
Keep guards in place and in working order.
◾
Keep hands and feet away from the cutting area.
◾
Store brush cutter indoors - When not in use the
brush cutter should be stored indoors in a dry and high
or locked-up place with the battery pack removed- out
of reach of children.
10
56 VOLT LITHIUM-ION REAR MOTOR BIKE-HANDLE BRUSH CUTTER — BCX3800
◾
Before using the brush cutter and after any impact,
check for signs of wear or damage and repair as
necessary.
◾
If the equipment should start to vibrate abnormally,
stop the motor, remove the battery pack from the
brush cutter and check immediately for the cause.
Vibration is generally a warning of trouble. A loose
cutting unit may vibrate, crack, break or come off the
brush cutter, which may result in serious or fatal injury.
Make sure that the cutting unit is properly installed
and securely fastened. If the cutting unit loosens after
fixing it in position, replace it immediately. Never use a
brush cutter with a loose cutting unit.
◾
To reduce the risk of injury, never work on a ladder
or on any other insecure support. Never hold the
cutting unit above waist height.
◾
Check the cutting unit at regular short intervals
during operation, or immediately if there is a
noticeable change in cutting behavior.
◾
For best results, your battery should be charged in
a location where the temperature is greater than
5° C and less than 40° C. Do not store it outside or
in vehicles.
◾
Only use EGO authorized polymer trimmer line and
blade accessories, trimmer line and blade that are
designed for use with this brush cutter. Although
certain unauthorized units might be extremely
dangerous, and/or damaging to the tools.
◾
If you are approached, stop the motor and cutting unit.
◾
Warn the operator of the danger of blade thrust
(only using with 3-teeth blade).
◾
Blade thrust may occur when the spinning blade
contacts an object that it does not immediately cut.
◾
Blade thrust can be violent enough to cause the unit
and/or operator to be propelled in any direction, and
possibly lose control of the unit.
◾
Blade thrust can occur without warning if the blade
snags, stalls or binds.
◾
Blade thrust is more likely to occur in areas where it
is difficult to see the material being cut.
◾
Do not attach any blade to a unit without proper
installation of all required parts. Failure to use the
proper parts can cause the blade to fly off and
seriously injure the operator and/or bystanders.
Discard blades that are bent, warped, cracked,
broken, or damaged in any way. Use a sharp blade.
A dull blade is more likely to snag and thrust (only
using with 3-teeth blade).
◾
A coasting blade/line can cause injury while it
continues to spin after the motor is stopped or
trigger is released. Maintain proper control until
the blade/line has completely stopped rotating.
◾
Use only with EGO's battery packs and chargers listed
below:
BATTERY PACK CHARGER
BAX1500 CHX5500E
◾
Battery tools do not have to be plugged into an
electrical outlet; therefore, they are always in
operating condition. Be aware of possible hazards
even when the tool is not operating. Take care when
performing maintenance or service.
◾
Do not wash with a hose; avoid getting water in
motor and electrical connections.
◾
If situations occur that are not covered in this
manual, use care and good judgment. Contact the
EGO Customer Service Center for assistance.
SAVE THESE INSTRUCTIONS!
SPECIFICATIONS
3-teeth metal
Cutting unit Trimmer head
blade
Voltage
56V 56V
No-load Speed 4000-5800/min 4000-5800/min
Recommended
0°C-40°C
Operating Temperature:
Recommended
-20°C-70°C
Storage Temperature:
Cutting Line Type 2.4mm /
Cutting blade / ABB1203
Cutting Width 38cm 30cm
Weight 6.8kg 6.46kg
Measured sound 94.2dB(A) 96.3dB(A)
power level L K=1.8dB(A) K=2.1dB(A)
WA
Sound pressure level 81.9dB(A) 83.4dB(A)
at operator's ear L K=2.5dB(A) K=4.1dB(A)
PA
Guaranteed sound
power level L 96dB(A) 98dB(A)
WA
(according to 2000/14/EC)
Left 1.9m/s 2 1.9m/s 2
Handle K=1.5m/s K=1.5m/s
2 2
Vibration a
h
Right 1.5m/s 2 1.3m/s 2
Handle K=1.5m/s 2 K=1.5m/s 2
56 VOLT LITHIUM-ION REAR MOTOR BIKE-HANDLE BRUSH CUTTER — BCX3800
◾
The declared vibration total value has been measured
in accordance with a standard test method and may be
used for comparing one tool with another;
◾
The declared vibration total value may also be used in
a preliminary assessment of exposure.
NOTICE:
The vibration emission during actual use of the
power tool can differ from the declared value in which the
tool is used; In order to protect the operator, user should wear
gloves and ear protectors in the actual conditions of use.

PACKING LIST

PART NAME QUANTITY
Brush Cutter 1
3-teeth blade with Sheath 1
Guard Assembly 1
Nut 1
Outer Flange 1
Hex Wrench 1
Multi-Function Wrench 1
Hip-pad 1
Operator's manual 1
DESCRIPTION
KNOW YOUR BRUSH CUTTER (Fig. A)
1. Trimmer Line
2. Guard Assembly
3. Shaft
4. Trigger
5. Lock-off Button
6. Wing Bolt
7. Hook
8. Socket
9. Guard Plate
10. Bike Handle
11. Sealing Screw
12. Shaft-locking Hole
13. Line-cutting Blade
14. Guard Accessory
15. 3-teeth Blade
16. Blade Sheath
11
EN