Publicidad
Idiomas disponibles
Idiomas disponibles
SAFETY WARNINGS AND INSTRUCTIONS: CHARGING THE DRILL
1. This manual contains important safety and operating instructions.
2. Before using battery charger, read all instructions and cautionary markings on (1)
battery charger, (2) battery, and (3) product using battery.
3.
CAUTION: To reduce the risk of injury, charge only Black & Decker Power Packs.
Other types of batteries may burst causing personal injury and damage.
4. Do not expose charger to rain or snow.
5. Use of an attachment not recommended or sold by Black & Decker may result in a risk
of fire, electric shock, or injury to persons.
6. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when
disconnecting charger.
7. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise
subjected to damage or stress.
8. An extension cord should not be used unless absolutely necessary. Use of improper
extension cord could result in a risk of fire, electric shock or electrocution.
a. Two-wire cords can be used with 2-wire or 3-wire extension cords. Only round jacketed
extension cords should be used, and we recommend that they be listed by
Underwriters Laboratories (U.L.). If the extension is to be used outside, the cord must
be suitable for outdoor use. Any cord marked for outdoor use can also be used for
indoor work. The letters "W" or "WA" on the cord jacket indicate that the cord is suitable
for outdoor use.
b. An extension cord must have adequate wire size (AWG or American Wire Gauge) for
safety, and to prevent loss of power and overheating. The smaller the gauge number of
the wire, the greater the capacity of the cable; that is, 16 gauge has more capacity than
18 gauge. When using more than one extension to make up the total length, be sure
each extension contains at least the minimum wire size.
C H A RT FOR MINIMUM WIRE SIZE (AWG)OF EXTENSION CORDS
N A M E P L ATE RATING AMPS – 0 – 10.0
Total Extension Cord Length (ft)
2 5
Wire Gauge
1 8
9. Use only the supplied charger when charging your drill. The use of any other charger
could damage the drill or create a hazardous condition.
10. Use only one charger when charging.
11. Do not attempt to open the charger or the drill. There are no customer serviceable
parts inside. Return to any authorized Black & Decker service center.
12. DO NOT incinerate the drill or battery packs even if they are severely damaged or
completely worn out. The batteries can explode in a fire.
13. Do not incinerate the batteries. They can explode in a fire. A small leakage of liquid
from the battery cells may occur under extreme usage, charging or temperature condi-
tions. This does not indicate a failure. However, if the outer seal is broken and this
leakage gets on your skin:
a. Wash quickly with soap and water.
b. Neutralize with a mild acid such as lemon juice or vinegar.
c. If the battery liquid gets in your eyes, flush them with clean water for a minimum of 10
minutes and seek immediate medical attention. MEDICAL NOTE: The liquid is a 25-
35% solution of potassium hydroxide.
CHARGING THE POWER PACK
THE BATTERIES IN YOUR POWER PACK ARE NOT F U L LY CHARGED AT T H E
FA C TO RY. BEFORE ATTEMPTING TO CHARGE THEM, T H O R O U G H LY READ A L L O F
THE SAFETY I N S T R U C T I O N S .
The 3 hour charger is designed to use standard household 120 volt 60 Hz power.
1. Plug the charger into any standard 120 Volt 60 Hz electrical outlet.
2. Insert the power pack into the charger as shown in Figure 1. While charging, your
battery pack may become warm to the touch; this is normal.
3. Remove pack from the charger and place in tool as shown in Fig. 2.
NOTE: To remove the battery from the tool, press in on the release buttons on both
sides of the battery and pull out.
I M P O RT ANT CHARGING NOTES
1. After normal usage, your power pack should be fully charged in 3 to 6 hours. If the
power pack is run-down completely, it may take up to 6 hours to become fully charged.
Your power pack was sent from the factory in an uncharged condition. Before attempt-
ing to use it, it must be charged for at least 9 hours.
2. DO NOT charge the power pack in an air temperature below 40°F or above 105°F. This
is important and will prevent serious damage to the power pack. Longest life and best
performance can be obtained if power pack is charged when air temperature is about
75°F.
3. While charging, the charger may hum and become warm to touch. This is a normal
condition and does not indicate a problem.
4. If the power pack does not charge properly—(1) Check current at receptacle by plug-
ging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light
switch which turns power off when you turn out the lights. (3) Move charger and power
pack to a surrounding air temperature of 40°F to 105°F. (4) If the receptacle and tem-
perature are OK, and you do not get proper charging, take or send the power pack and
charger to your local Black & Decker service center. See Tools Electric in yellow pages.
5. The power pack should be recharged when it fails to produce sufficient power on jobs
which were easily done previously. DO NOT CONTINUE using product with its power
pack in a depleted condition.
6. To prolong power pack life, avoid leaving the power pack on charge for extended periods
of time (over 30 days without use). Although overcharging is not a safety concern, it can
significantly reduce overall power pack life.
7. The power pack will reach optimum performance after being cycled 5 times during
normal usage. There is no need to run the batteries down completely before recharging.
Normal usage is the best method of discharging and recharging the batteries.
SAFETY WARNINGS AND INSTRUCTIONS: DRILLS
1. Hold drill firmly to control the twisting action of the drill. See Figure 3.
2. When attaching accessories in the drill chuck, hand tighten the keyless chuck firmly.
WARNING: Drill may stall (if overloaded or improperly used) causing a twist. A l w a y s
expect the stall. Grip the drill firmly to control the twisting action (see Fig. 3) and prevent loss
of control which could cause personal injury. If a stall does occur, release the trigger
immediately and determine the reason for the stall before re-starting.
OPERATING INSTRUCTIONS
TRIGGER SWITCH & REVERSING BUTTON (FIGURE 4)
The drill is turned ON and OFF by pulling and releasing the trigger switch shown in Figure 4.
The farther the trigger is depressed, the higher the speed of the drill. A f o r w a r d / r e v e r s e
control button determines the direction of the tool and also serves as a lock off button. To
select forward rotation, release the trigger switch and depress the forward/reverse control
button. To select reverse, depress the forward/reverse control button the opposite direction.
The center position of the control button locks the tool in the off position. When changing the
position of the control button, be sure the trigger is released.
TORQUE CONTROL (FIGURE 5)
This tool is fitted with a collar to select the operating mode and to set the torque for
tightening screws. Large screws and hard workpiece materials require a higher torque
setting than small screws and soft workpiece materials.
•
For drilling in wood, metal and plastics, set the collar to the drilling position symbol
•
For screwdriving, set the collar to the desired setting. If you do not yet know the
appropriate setting, proceed as follows:
•
Set the collar to the lowest torque setting.
•
Tighten the first screw.
•
If the clutch ratchets before the desired result is achieved, increase the collar setting and
continue tightening the screw. Repeat until you reach the correct setting. Use this setting
for the remaining screws.
KEYLESS CHUCK (FIGURE 6 )
To insert a drill bit or other accessory:
1. Grasp the rear half of the chuck with one hand and use your other hand to rotate the
front half in the counterclockwise direction, as viewed from the chuck end.
2. Insert the bit or other accessory fully into the chuck, and tighten securely by holding the
rear half of the chuck and rotating the front portion in the clockwise direction as viewed
from the chuck end.
5 0
7 5
1 0 0
125
150
1 8
1 6
1 6
14
14
WA R N I N G : Do not attempt to tighten drill bits (or any other accessory) by gripping the front
part of the chuck and turning the tool on. Damage to the chuck and personal injury may
occur when changing accessories.
SCREW DRIVING
For driving fasteners, the reversing button should be pushed to the left. Use reverse (button
pushed to the right) for removing fasteners. When moving from forward to reverse, or vice
versa, always release the trigger switch first.
ON BOARD BIT STORAGE
A bit storage slot is built-in to the area just above the battery. Use the magnetic bit tip holder
in conjunction with the 1 inch bit tips stored in the removable rubber cap on the end of the
d r i l l .
D R I L L I N G
•
Use sharp drill bits only.
•
Support and secure work properly, as instructed in the Safety Instructions.
•
Use appropriate and required safety equipment, as instructed in the safety instructions.
•
Secure and maintain work area, as instructed in the safety instructions.
•
Run the drill very slowly, using light pressure, until the hole is started enough to keep the
drill bit from slipping out of it.
•
Apply pressure in a straight line with the bit. Use enough pressure to keep the bit biting
but not so much as to stall the motor or deflect the bit.
•
Hold the drill firmly with two hands to control its twisting action.
•
DO NOT CLICK THE TRIGGER OF A STALLED DRILL OFF AND ON IN AN ATTEMPT
TO START IT. DAMAGE TO THE DRILL CAN RESULT.
•
Minimize stalling on breakthrough by reducing pressure and slowly drilling through last
part of hole.
•
Keep the motor running while pulling the bit out of a drilled hole This will help reduce
jamming.
•
Make sure switch turns drill on and off.
WA R N I N G : It is important to support work properly and to hold the drill firmly to prevent
loss of control which could cause personal injury If you have questions on how to operate
tool, call: 1 - 8 0 0 - 5 4 4 - 6 9 8 6 .
DRILLING IN WOOD
Holes in wood can be made with the same twist drill bits used for metal or with spade bits.
These bits should be sharp and should be pulled out frequently when drilling to clear chips
from the flutes.
DRILLING IN META L
Use a cutting lubricant when drilling metals. The exceptions are cast iron and brass which
should be drilled dry. The cutting lubricants that work best are sulfurized cutting oil or lard oil.
DRILLING IN MASONRY
Use carbide tipped masonry bits. Refer to Drilling section. Keep even force on the drill but not
so much that you crack the brittle material. A smooth, even flow of dust indicates the proper
drilling rate.
P r o b l e m
• Unit will not start.
• Battery will not charge.
For assistance with your product, visit our website www.blackanddecker.com for the loca-
tion of the service center nearest you or call the BLACK & DECKER help line at
1-800-544-6986.
MAINTENANCE
Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool;
never immerse any part of the tool into a liquid. I M P O R TA N T: To assure product SAFETY
and RELIABILITY, repairs, maintenance and adjustment should be performed by
authorized service centers or other qualified service organizations, always using
identical replacement parts.
THE RBRC™ SEAL
The RBRC™ (Rechargeable Battery Recycling Corporation)Seal on the nickel-cadmium
battery (or battery pack) indicates that the costs to recycle the battery (or battery pack) at the
end of its useful life have already been paid by Black & Decker. In some areas, it is illegal to
place spent nickel-cadmium batteries in the trash or municipal solid waste stream and the
RBRC program provides an environmentally conscious alternative.
RBRC in cooperation with Black & Decker and other battery users, has established programs
in the United States and Canada to facilitate the collection of spent nickel-cadmium batteries.
Help protect our environment and conserve natural resources by returning the spent nickel-
cadmium battery to an authorized Black & Decker service center or to your local retailer for
recycling. You may also contact your local recycling center for information on where to drop
o ff the spent battery, or call 1 - 8 0 0 - 8 - B AT T E RY.
ACCESSORIES
Recommended accessories for use with your tool are available from your local dealer or
authorized service center. If you need assistance regarding accessories, please call:
1-800-544-6986. The following accessories should be used only in the sizes specified below:
BITS, META L DRILLING – Up to 3/8" (9.5mm); BITS, MASONRY DRILLING – Up to 3/8"
(9.5mm); WOOD DRILLING – Up to 1/2" (12.7mm).
WA R N I N G :
The use of any accessory not recommended for use with this tool could be
h a z a r d o u s .
SERVICE INFORMATION
All Black & Decker Service Centers are staffed with trained personnel to provide customers
with efficient and reliable power tool service. Whether you need technical advice, repair, or
genuine factory replacement parts, contact the Black & Decker location nearest you. To find
your local service location, refer to the yellow page directory under "Tools—Electric" or call:
1-800-544-6986 or visit www. b l a c k a n d d e c k e r. c o m
FULL TWO-YEAR HOME USE WARRANTY
Black & Decker (U.S.) Inc. warrants this product for two years against any defects in material
or workmanship. The defective product will be replaced or repaired at no charge in either of
two ways.
The first, which will result in exchanges only, is to return the product to the retailer from whom
.
it was purchased (provided that the store is a participating retailer). Returns should be made
within the time period of the retailer's policy for exchanges (usually 30 to 90 days after the
sale). Proof of purchase may be required. Please check with the retailer for their specific
return policy regarding returns that are beyond the time set for exchanges.
The second option is to take or send the product (prepaid) to a Black & Decker owned or
authorized Service Center for repair or replacement at our option. Proof of purchase may be
required. Black & Decker owned and authorized Service Centers are listed under "To o l s -
Electric" in the yellow pages of the phone directory and available on our website
w w w. b l a c k a n d d e c k e r. c o m.
This warranty does not apply to accessories. This warranty gives you specific legal rights and
you may have other rights which vary from state to state. Should you have any questions,
contact the manager of your nearest Black & Decker Service Center. This product is not
intended for commercial use.
Free Warning Label Replacement: If your warning labels become illegible or are missing,
call 1-800-544-6986 for a free replacement.
Imported by
Black & Decker (U.S.) Inc.,
701 E. Joppa Rd.
Towson, MD 21286 U.S.A.
TROUBLESHOOTING
Possible Cause
Possible Solution
• Battery not installed properly.
• Check battery installation.
• Battery not charged.
• Check battery charging
r e q u i r e m e n t s .
• Battery not inserted into charger.
• Insert battery into charger
until red LED appears.
• Charger not plugged in.
• Plug charger into a working
outlet. Refer to "Important
Charging Notes" for more
d e t a i l s .
• Check current at receptacle
by plugging in a lamp or other
a p p l i a n c e .
• Check to see if receptacle is
connected to a light switch
which turns power off when
you turn out the lights.
• Surrounding air temperature
• Move charger and tool to a
too hot or too cold.
surrounding air temperature
of above 40 degree F(4 , 5°C)
or below 105 degree F
(+ 4 0 , 5°C ).
See 'Tools-Electric'
– Yellow Pages –
for Service & Sales
Publicidad
