Publicidad
Idiomas disponibles
Idiomas disponibles
HARDWARE MOUNTED
Used where additional security is required (top of the stairs etc.).
Warning: DO NOT MOUNT HINGES INTO SHEETROCK OR PLASTER. HARDWARE IS
INCLUDED FOR USE IN SOLID MATERIALS ONLY, SUCH AS WOOD OR METAL.
BEFORE BEGINNING YOU MUST DETERMINE WHICH VERSION OF GATE YOU
HAVE BY MEASURING THE BUMPER SPACING ON YOUR GATE. SEE FIGURE 7.
If this measures 21 3/8", follow dimension and figures A. If it measures 17 3/8", follow
dimensions and figures B.
STEP 1
Hold the gate so the locking handle is on the opposite side of the area
accessible to the child and determine on which side you want the gate hinges.
STEP 2
Slide both gate hinges onto the hinge side of the gate and fasten lower hinge
with smaller screw provided (do not fasten top at this time). See Figure 8.
STEP 3
Fasten both the casement hinges to the doorway using the longer screws
provided. Mount upper casement hinge with hinge facing down, mount lower
casement hinge with hinge facing up. See Figure 9.
STEP 4
Determine the direction you desire the gate to swing.
Gate to swing towards you—place bottom gate hinge onto bottom
casement hinge using the hole in the hinge that is closest to you.
Gate to swing from you—Use the hole in the gate hinge furthest from you.
DO NOT ALLOW GATE TO SWING OVER THE STAIRS.
STEP 5
Slide the gate hinge on the top of the gate up to the casement hinge and
fasten the top gate hinge with the small screw provided.
STEP 6
Place tape pads in recessed area of door sockets.
STEP 7 (for bumper spacing 21 3/8" apart)
Remove protective cover sheet from one of the sockets, with U upright. Measuring from the bottom of the
socket, place on a flat, even surface 3" above the floor. Mount second socket 23" from the floor (measured
from the bottom of the sockets). See Figure 10.
Screws, in addition to tape pads, may be used for added security. Use two longer screws provided.
Warning: SCREWS ARE REQUIRED IF GATE IS INSTALLED OVER THE STAIRS.
STEP 7 (for bumper spacing 17 3/8" apart)
Remove protective cover sheet from one of the sockets, with U upright. Measuring from the bottom of the
socket, place on a flat, even surface 5" above the floor. Mount second socket 21" from the floor (measured
from the bottom of the sockets). See Figure 10.
Screws, in addition to tape pads, may be used for added security. Use two longer screws provided.
Warning: SCREWS ARE REQUIRED IF GATE IS INSTALLED OVER THE STAIRS.
OPERATION
To close the gate: Expand gate so the 2 bumpers fit in the sockets. Rotate locking handle and insert handle
tab into the slot that gives you enough tension to secure the gate.(see figure 2)
To open the gate: Lightly press down on the locking handle, twist handle outward and pull gently away from
the gate. Slide gate together and swing open.
CLEANING INSTRUCTIONS: Wash with warm water using mild liquid soap. Use a soft cloth to avoid
scratching the gate. Rinse with clear water and wipe dry with a soft cloth. NOTE: Never use solvents,
chemicals, scouring powders and sharp tools when cleaning the gate.
Figure 7
A = 21 3/8"
B = 17 3/8"
SLIDE GATE HINGE
PAST MOUNTING HOLE
WITH TAB ORIENTATED
AS SHOWN (DO NOT
FASTEN AT THIS TIME)
DRILL
/
" (1.59mm)
1
16
PILOT HOLES
A = 23 3/8"
B = 21 3/8"
A = 22 5/8"
B = 20 5/8"
Figure 9
Figure 9
A = 3 3/4"
A = 4 1/2"
B = 5 3/4"
B = 6 1/2"
Figure 10
Page 4
MOUNT IN THIS
HOLE FOR GATE
TO SWING
TOWARD YOU
MOUNT IN THIS
HOLE FOR GATE
TO SWING AWAY
Figure 8
Figure 8
A = 23"
B = 21"
A = 3"
B = 5"
Publicidad
