Code Search - Vivanco UR Zap 2 Manual De Instrucciones

(GB) Instructions
UR Zap 2 remote control for TV sets, satellite receivers
and cable boxes
1 Inserting the batteries
Open the battery flap on the back of the remote control and
insert 2 alkaline AAA batteries. Check that the polarity
markings on the batteries and in the battery compartment are
correctly lined up (+=+), then close the flap carefully. – Always
use undamaged, fully charged batteries.
2 Adapting to appliances
In order to control your appliances you must adapt or set the
remote control to them. There are two ways of doing so: direct
control code entry or code search.
2.1 Direct control code entry using the enclosed list
Example: setting to control a Panasonic television set:
2.1.1 Using the TV button, select to control a television set
(TV).
2.1.2 The enclosed list gives, for example, the Panasonic
Code 241.
Please make sure you have selected the correct list for
television sets (TV).
2.1.3 To prepare code entry, keep the Mute (sound on/off)
button and the PWR (appliance on/off) button pressed
simultaneously(!) until the lamp (LED) lights constantly.
2.1.4 Then enter the code numbers as follows:
2.1.4.1 1st number of code (hundreds = Volume -): Press the
VOL- (volume down) button- twice for 2 of 241. Press as
often as the number indicates. (1=once, 2 = twice, etc.)
2.1.4.2 2nd number of code (tens = Channel+): Press the
CH+ (channel up) button four times for the 4 of 241.
2.1.4.3 3rd number of code (ones = Volume+): Press the
VOL+ (volume up) button once for the 1 of 241.
2.1.4.4 Finally, press the Mute button again briefly. The lamp
(LED) goes out. To enter a 0, do not press any button. If
incorrect entries are made the remote control blinks for about 3
seconds.
2.1.5 Then test the control code setting by trying to control (in
this example) your television set. If it does not work at all or not
correctly try a different code from the list or code search (see
below).
2.1.6 To make the setting for a satellite receiver or a cable
box, press the SAT button instead of TV and enter a satellite
code accordingly.

2.2 Code search

If the brand of your appliance is not in the list or none of the
codes given fits, we recommend a code search.
2.2.1 Switch on the appliance to be controlled. Program is
running. A channel number, for example, appears in the
display of your satellite receiver.
2.2.2 Press the TV or SAT appliance button according to the
appliance type to be controlled, e.g. SAT.
2.2.3 Keep the ON/OFF PWR (appliance on/off) and Mute
buttons pressed simultaneously(!) until the lamp lights
constantly.
2.2.4 Press the ON/OFF PWR (appliance on/off) button once
briefly.
2.2.5 The UR Zap 2 emits a different signal every 1.3
seconds. When your appliance reacts, very quickly press the
Mute button to confirm a functioning control code. – It is
advisable to have your finger already placed on the Mute
button so that you can react quickly enough. Otherwise the UR
Zap 2 emits the next signal before you have reacted.
2.2.6 Finally, test the control code setting by trying to control
your SAT appliance. If it does not work correctly, please try the
code search again.
Note: Remember to switch your appliance, e.g. SAT, back on
again if you wish to continue searching.
Vivanco GmbH, Ewige Weide 15, D-22926 Ahrensburg, Tel:+49 (0)4102
231235, Fax: +49(0)4102 231444, e-Mail: hotline@vivanco.de 2