Publicidad
Idiomas disponibles
Idiomas disponibles
If a digital signal is not available at the selected
input, the message „NO SIGNAL" will appear
in the display:
27 eject
Opens the cD compartment.
28 Stop - Play/Pause
Right button: Starts or pauses the playback
from a cD.
Left button: Stops a cD that is playing.
29 Search
High-speed rewind and fast forward. Remains
active as long as the button is depressed.
INITIAl OPeRATION
• Place the McD 1050 on an even surface. Observe the relevant clearance gaps as specified under
"Important safety instructions".
IMPORTANT: Do not place any objects on top of the device (magazines, cD/record cases, etc.).
The ventilation slots located on top of the device must be unobstructed at all times!
• connect an audio output (analogue or digital) to a suitable amplifier. Also refer to the operating
instructions for the device when doing this.
• connect the supplied mains cable to the rear and then insert the other end into a 230V socket.
• Actuate the on/off switch on the rear side, the device is now in the standby mode.
• Switch on the device using the ON/STANDBY button on the front panel or the remote control.
• When the tubes have heated up the device is ready for use.
TUBe RePlACeMeNT
The device has a high quality preamplifier stage which is equipped with two tubes. The tubes have a
very long service life when used under normal operating conditions (min. 20,000-50,000 hours).
If it is necessary to replace the tubes, please refer to a specialist dealer.
SeRVICe AND TeCHNICAl PROBleMS
If you should encounter any technical problems, please contact your specialist dealer or
Magnat Audio-Produkte GmbH, Tel.: 02234807-0.
30 Skip
Playback starts at the beginning of the current
or next track.
Pressing the left button twice starts playback at
the beginning of the previous track.
31 Headphone
Increases (+) or reduces (-) the volume of the
headphone jack between -64dB and 0dB in
1dB steps.
The non-numbered buttons are reserved for
operating the Magnat amplifier MA 1000 and
have no function for the McD 1050.
SPeCIFICATIONS
Frequency response:
Signal to noise ratio :
channel separation:
Output voltage:
Harmonic distortion:
Digital outputs:
Digital inputs:
Supported sampling frequencies: 44.1/48/88.2/96/176.4/192kHz
Supported Bit depths:
Upsampling:
Mains voltage:
Electricity consumption:
Type
Standby
Fitted with:
Playable formats:
Dimensions (wxhxd):
Main device:
Main device incl. operational
elements/connecting terminals:
Remote control:
Weight:
For further information please visit our website: http://www.magnat.de.
11
5 Hz – 20 kHz (+/- 0.5 dB)
109 dB (20 Hz – 20 kHz, A-weighted)
> 106 dB (1 kHz)
2.0 V (10 kOhm)
< 0.0012%
1 x optical (Toslink™)
1 x coaxial (RcA)
1 x USB 2.0 type B port
1 x optical (Toslink™)
1 x coaxial (RcA)
16/24Bit
Switchable upsampling function to 192 kHz/24 bit
for cDs and digital inputs
230 VAc / 50 Hz
25 W
0,5 W
2 x Ecc 88
cD-DA, HDcD, cD-R, cD-RW
434 x 90 x 330 mm
434 x 90 x 345 mm
47 x 198 x 23 mm
7.5 kg
Publicidad
