Operating Instructions Cont., To Replace Paper Filter Dust Bag - Oreck XL U2000R-1 Guia Del Usuario

8. DO NOT run the vacuum cleaner over cord. The revolving
brush could damage the cord.
9. Use caution when vacuuming over area rug edges &
fringe.
Disposable Paper Filter Dust Bags
Disposable paper filter dust bags play a very important role in
the efficiency of your ORECK vacuum cleaner. The purpose of
the filter bag is to trap dirt, but at the same time it must be
porous enough to allow air to pass through. If the filter bag
becomes clogged, no air can pass through the cleaner and
cleaning cannot take place, regardless of the cleaner's power.
To keep your cleaner operating at maximum efficiency, change
the dust bag frequently. DO NOT FILL ABOVE THE LINE
INDICATED ON THE DUST BAG.
Be sure the disposable paper filter dust bag is installed
properly.
All paper dust bags are not the same. Your ORECK
disposable dust bags have been designed to be used with
the ORECK cleaner. Using bags other than genuine ORECK
disposable bags will affect the cleaning ability of your
cleaner and could cause damage to it.
The Belt
The belt on your vacuum cleaner controls the speed of the
revolving brush and is very important for the effective operation
of the cleaner. If the belt becomes stretched or cut, it will cause
the revolving brush to stop completely or slow down. See
instructions in the manual for replacing belt.
An extra belt is stored in the baseplate of your cleaner.
When buying replacement belts, use ONLY ORECK genuine
belts. Belts other than ORECK belts will not operate the
revolving brush correctly and may create undue stress
which will cause damage to the motor and brush bearings.
Using belts other than ORECK belts will void the warranty.
Lubrication
The vacuum cleaner motor bearings are factory lubricated and
sealed. Further lubrication is not required.
General Cleaner Care
At least once a month, check for and remove excessive lint,
string or hair from revolving brush.
Wipe the outside of the cleaner with a damp cloth. Also, clean
manufacturer's recommended methods of cleaning. The metal
strip on the base of the cleaner could be damaged if used on
concrete or abrasive surfaces, and, therefore, cause damage to
wood floors, soft (vinyl, asphalt tile, etc.) floor surfaces and
polished floor finishes. The roller brush may also scuff very soft
finishes. Do not operate the unit while in the upright and locked
position. Do not let the unit run while in any one stationary
position for any period of time. Keep the unit moving while in
operation.
E N G
the connector deflector
assembly area, base of cleaner
and fan housing area. If there is
dust in the outer bag, vacuum it
or shake it out.
A little preventative mainte-
nance will keep your cleaner
looking new and will ensure
continued cleaning effec-
tiveness.
CAUTION—Wood Floors, Soft
(Vinyl, Asphalt Tile, etc.) Floor
Surfaces and Polished Floor
Finishes
Use floor and floor finish
L I S H
T R
o eplace
D
ust
WARNING: Unplug cord from
electrical outlet before servicing.
A
B
Cord-Lock Instructions
WARNING: Unplug cord from electrical
outlet before servicing or removing cord-
lock.
Assembly:
1. Connect plug and receptacle.
2. Snap cord into lock.
3. Rotate insert until secure against
plug.
4. Ensure rotation is as depicted
to ensure proper engagement.
Disassembly:
1. Remove cord from lock
2. Disconnect plug and receptacle.
5
F
ilter
B
ag
BAG INSTALLATION:
1. Hook bottom of bag collar
opening under lip "B" of
connector assembly. Pull up
on bag collar and snap over
lip "A" of connector.
2. Press on edges of bag collar
to insure bag is completely
installed.
IMPORTANT: Check to make
sure bag collar is behind lips
"A" and "B".
If it is not, dust will leak into
outer bag. When filter bag is
in place, close outer bag
with zipper fastener.
Assembly Disassembly