Silverline 802165 Traducción Del Manual Original página 9

802165
Performing a straight cut
• Use the measuring scale located on the Table Surface (4) to accurately determine the
size of the cut
1. Loosen the Fence Locking Knobs (10), position the Straight Fence (9) in the desired
location and retighten the Fence Locking Screws
2. With the machine on, press the workpiece firmly against the Straight Fence and
slowly feed the workpiece into the Cutting Disk (5)
NOTE: Do not force the workpiece into the blade, excessive pressure can cause kickback,
and damage to the blade/workpiece.
Performing a mitre cut
NOTE: Use the Mitre Guide (11) to perform accurate 45° cuts.
1. Loosen the Straight Fence Locking Knobs (10)
2. Place the Mitre Guide (11) against the Straight Fence (9) (Image G)
3. Adjust the Straight Fence position, using the measuring scale as reference, to
accurately measure the cut
4. Lock the Straight Fence into position, by tightening the Straight Fence Locking Knobs
5. Use the Mitre Guide to feed the tile into the Cutting Disk (5)
Performing a bevel cut
• To adjust the bevel angle of the Table Surface (4):
1. Undo Bevel Angle Lock Front (8) and Rear (7)
2. Tilt the table to the desired angle, and Lock the Bevel Angle Lock Front and Rear to
secure the position, (Image H)
Note:
The bevel angle is displayed on a graduation scale beneath the Bevel Angle Lock
Front.
• Ensure the Straight Fence (9) is secure, and use it as a guide when cutting the
workpiece
• Take extra care of the Cutting Disk (5) when performing bevel cuts
Accessories
• A range of accessories and consumables, including Tile Cutting Diamond Disc
(993035) is available from your Silverline stockist. Spare parts can be obtained from
toolsparesonline.com
Maintenance
WARNING: ALWAYS disconnect from the power supply before carrying out any inspection,
maintenance or cleaning.
Replacing the cutting disk
WARNING: ALWAYS wear suitable cut proof gloves when handling the Cutting Disk (5). Not
doing so may result in cuts, or harm to the operator.
1. Remove the Water Sump (1), ensure the blade housing area is dry and turn the
machine on its side so the blade housing is facing upwards
2. Unscrew and remove the four Philipps head screws holding the blade cover on
(Image I)
3. Remove the blade cover to reveal the Cutting Disk (5) and spindle assembly
(Image J)
4. Place the Spanner (13) over the locking nut, and use the Spindle Spanner (14) to
secure the spindle. Undo the locking nut using the Spanner (Image K)
5. Remove the outer flange from the spindle to reveal the disk. Pull the disk off the
inner flange
6. Replace the Cutting Disk, being sure that it is the correct orientation and that it is
correctly seated on the inner flange (Image L)
Note: The spindle will spin in an anticlockwise direction when viewed with the blade cover
removed. Ensure the correct disk is installed in the correct orientation.
7. Reinstall the outer flange and tighten the lock nut onto the spindle
8. Replace the blade cover and return the tile cutter to its normal working position
9. Switch the machine on, allow the Cutting Disk to get up to speed, and check that it
is running smoothly and 'true'
General inspection
• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, prior to each use, for damage or wear. Repairs
should be carried out by an authorised Silverline service centre. This advice also applies
to extension cords used with this tool
Cleaning
• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly,
and shorten the machine's service life. Clean the body of your machine with a soft
brush, or dry cloth. If available, use clean, dry, compressed air to blow through the
ventilation holes
• Clean the tool casing with a soft damp cloth using a mild detergent. Do not use alcohol,
petrol or strong cleaning agents
• Never use caustic agents to clean plastic parts
Lubrication
• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant
Brushes
• Over time the carbon brushes inside the motor may become worn
• Excessively worn brushes may cause loss of power, intermittent failure, or visible
sparking
• If you suspect that the brushes may be worn, have them replaced at an authorised
Silverline service centre
Storage
• Store this tool carefully in a secure, dry place out of the reach of children
www.silverlinetools.com
450W Tile Cutter
9