Jensen S168244 Instrucciones De Instalación

Bisagra de 125 Grados
10
Bisagra de 170 Grados
12
11
PIEZAS DE SERVICIO
Key
S168244 S135244
No. Descripcion
1 Ensamblaje De la Puerta 107-661-01 107-661-01P
2 Montaje de bisagra JRP595 JRP595
Tornillo, bisagra 10-163-01 10-163-01
3
**Tapones 29-826-xx 29-826-xx
4
29-827-xx 29-827-xx
5 **Cubierta del tornillo
* *
6 Tornillo de montaje #8 x 1 1/2*
7 **Soporte de estante 29-842-xx 29-842-xx
8 Estante de vidrio 31-185-01 31-185-01
Tira de Topes 29-846-01 29-846-01
9
Cubierta De la Bisagra (125 grados) 42-596-01 42-596-01
10
- -
11 El Sujetador negro (170 grados)
- -
12 Cierre Silencioso (170 gardos)
Key
S335244 S335246
No. Descripcion
107-663-01P 107-663-01P
1 Ensamblaje De la Puerta
2 Montaje de bisagra JRP586D JRP586D
Tornillo, bisagra 10-163-01 10-163-01
3
Tapones 29-826-xx 29-826-xx
4
29-827-xx 29-827-xx
5 Cubierta del tornillo
* *
6 Tornillo de montaje #8 x 1 1/2*
29-842-xx 29-842-xx
7 Soporte de estante
8 Estante de vidrio 31-185-01 31-186-01
Tira de Topes 29-846-01 29-846-01
9
Cubierta De la Bisagra (125 grados) - -
10
42-594-01 42-594-01
11 El Sujetador negro (170 grados)
12 42-586-02 42-586-02
Cierre Silencioso (170 gardos)
* Ferreteria estandar - puede ser comprado localmente.
** Especifique (-01) blanco o (-02) negro donde "xx" se localiza
Pida los piezas de reemplazo por "NUMERO de PIEZA" - No por el "NUMERO DOMINANTE"
(Bisagra de 125 grados mostrada)
S268244 S268246 S235244 S235246 S368244
107-662-01 107-662-01 107-662-01P 107-662-01P 107-663-01
JRP595 JRP595 JRP595 JRP595 JRP586D
10-163-01 10-163-01 10-163-01 10-163-01 10-163-01
29-826-xx 29-826-xx 29-826-xx 29-826-xx 29-826-xx
29-827-xx 29-827-xx 29-827-xx 29-827-xx 29-827-xx
* * * *
29-842-xx 29-842-xx 29-842-xx 29-842-xx 29-842-xx
31-185-01 31-186-01 31-185-01 31-186-01 31-185-01
29-846-01 29-846-01 29-846-01 29-846-01 29-846-01
42-596-01 42-596-01 42-596-01 42-596-01
- - - - 42-594-01
- - - - 42-586-02
S468244 S468246 S435244 S435246 S568244
107-665-01 107-665-01 107-665-01P 107-665-01P
LLAME COMPANIA
JRP586D JRP586D JRP586D JRP586D JRP586D
10-163-01 10-163-01 10-163-01 10-163-01 10-163-01
29-826-xx 29-826-xx 29-826-xx 29-826-xx 29-826-xx
29-827-xx 29-827-xx 29-827-xx 29-827-xx 29-827-xx
* * * *
29-842-xx 29-842-xx 29-842-xx 29-842-xx 29-842-xx
31-187-01 31-192-01 31-187-01 31-192-01 31-187-01
29-846-01 29-846-01 29-846-01 29-846-01 29-846-01
- - - -
42-594-01 42-594-01 42-594-01 42-594-01 42-594-01
42-586-02 42-586-02 42-586-02 42-586-02 42-586-02
8
MODEL:
S168244 , S135244
S268244 , S268246
S235244 , S235246
S368244 , S368246
S335244 , S335246
S468244 , S468246
S435244 , S435246
S568244 , S568246
RECESSED MOUNTED, STEEL BATH CABINETS
INSTALLATION of CABINET
1. Carefully remove all packing material. Place hardware
packages, shelves and door aside until needed.
2. Determine desired location of cabinet on wall. Mark wall
to show wall opening size (see dimension chart). Generally,
the recommended height to the center of the cabinet is 64"
from the floor. (Fig. 1)
3. CAUTION: Wall studs, plumbing or electrical lines that
interfere must be removed or relocated. Cut wall opening,
being careful not to damage the surrounding wall surface.
Insert framing to support all plaster board edges.
Fig. 1
S368246
107-663-01
JRP586D
10-163-01
29-826-xx
29-827-xx
* *
29-842-xx
31-186-01
29-846-01
- -
Fig. 3
42-594-01
42-586-02
S568246
LLAME COMPANIA
JRP586D
10-163-01
29-826-xx
29-827-xx
* *
29-842-xx
31-192-01
29-846-01
- -
42-594-01
42-586-02
INSTALLATION INSTRUCTIONS
MODEL WALL OPENING
NO. W
S168244 14 ¼
S135244 14 ¼
S268244 14 ¼
S268246 14 ¼
S235244 14 ¼
S235246 14 ¼
S368244 14 ¼
S368246 14 ¼
S335244 14 ¼
S335246 14 ¼
S468244 14 ¼
S468246 14 ¼
S435244 14 ¼
S435246 14 ¼
S568244 14 ¼
S568246 14 ¼
4. Prepare the mounting screws by placing the screws into the
clear plastic bases. (Fig. 2)
5. Note: For ease of installation, an additional person is
recommended.Insert cabinet into wall opening. (Fig.3) Ensure
the cabinet is plumb and level. If necessary use a carpenter's
level and shim corners of cabinet. Secure the wall studs
through the four (4) mounting holes inside cabinet, using the
screws that have been placed into the plastic bases. (Fig. 4)
Do not over tighten the mounting screws as the body side wall
may bend and prevent proper shelf installation. Only tighten
until they are flush with the body.
6. Snap the screw covers over the screw bases. (Fig. 5)
Fig. 2
Insert screw
through clear
plastic base
Fig. 4
Wall
Opening
Mounting
Screws
Cabinet
Body
1
OVERALL SIZE
H D W H D
24 4 15 25 5
24 4 15 25 5
24 4 15 25 5
24 6 15 25 7
24 4 15 25 5
24 6 15 25 7
24 4 15 25 5
24 6 15 25 7
24 4 15 25 5
24 6 15 25 7
24 4 15 25 5
24 6 15 25 7
24 4 15 25 5
24 6 15 25 7
24 4 15 25 5
24 6 15 25 7
Fig. 5
Snap on Cover
Cover
Screw
Base
Mounting
screwinto
mounting
hole
72-323-01D