Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
Installation
E
N
(continued)
G
L
I
S
4
Get ready to attach the main unit.
H
13
Front cover
A
A
A
8 Push nut a 6
= or > or ?
Space washer*
(A or B or C)a6
: Flat washer a 6
9 Spring washer a 6
6 Screw a 6
8 Push nut
= or > or ?
(No. 10-32 UNF)
Space washer*
q}] or
: Flat washer
A [t=1 mm {
1
/
25
q}] or
[No. 10 (5 mm‡)]
B [t=2 mm {
2
/
25
q}]a 6
C [t=3 mm {
3
/
25
9 Spring washer
[No. 10 (5 mm‡)]
6 Screw
[No. 10-32 UNF, L=32 mm {1
26
CY-VHD9401U/L
1
Open the display unit and remove the 2 screws.
Place your fi ngers at A (in 2 places) on the
panel, and slowly pull down the panel.
Note:
≥ Be careful not to scratch the surface of the
front cover when removing it.
≥ The screws you remove now will be needed
when you re-attach it to complete installation.
Keep them in a place where they will not be
lost.
2
Insert the screws (6), space washers A, B,
or C (=, >, or ?), fl at/spring washers (9
and :), and push nuts (8) in the main unit.
Keep the screws only loosely tightened until the
unit is attached to the base plate.
* Depending on the type of vehicle for the
installation, you may not need to use some
space washers. When the space washers
are to be used, make absolutely sure
that their height will be the same in all
6 locations. Consult your dealer for details.
Caution:
≥ Before installing the unit, be absolutely
sure to check that the screws do not
make any contact with the ceiling panel.
If some space is required between the
base plate and the unit, attach and
adjust the under cover (see next page).
q}]
1
/
4
For details on installing the under cover,
consult your dealer.
ª If some space is required between the base plate and the unit, attach the under cover
and adjust as follows.
8 Push nut
(No. 10-32 UNF)
A Space washer (D)
3
q}]
[t=80 mm {3
/
16
: Flat washer
Main unit
[No. 10 (5 mm‡)]
9 Spring washer
[No. 10 (5 mm‡)]
B Screw
[No. 10-32 UNF, L=100 mm {4q}]
C Screw
q} ‡ k 8 mm {
q}] a 6
[2.6 mm {
1
/
8
/
10
25
@ Under
cover
1
Insert the screws (B), space washers D (A),
fl at/spring washers (9 and :), and push nuts
(8) in the main unit and attach the base plate.
Caution:
≥ Before installing the unit, be absolutely
sure to check that the screws do not
make any contact with the ceiling panel.
2
Use the screws (for resin) (C) to attach the
accessory under cover (@) to the underside of
the main unit.
Note:
≥ Depending on the type of vehicle, there
may be differences in the gap between the
headliner and the main unit. For gaps, adjust
the under cover and screw as necessary.
CY-VHD9401U/L
E
N
G
L
I
S
H
14
27
Publicidad
Tabla de contenido
