Safety Guidelines; Unpacking; Assembly; Start-Up - Campbell Hausfeld PW2120 Manual De Instrucciones De Ensamblaje

Gasoline Powered Pressure Washers

Safety Guidelines

This manual contains information that
is very important to know and under-
stand. This information is provided for
SAFETY and to PREVENT EQUIPMENT
PROBLEMS. To help recognize this infor-
mation, observe the following symbols.
Danger indicates
DANGER
!
an imminently
hazardous situation which, if not
avoided, WILL result in death or seri-
ous injury.
Warning indicates
WARNING
!
a potentially haz-
ardous situation which, if not avoided,
COULD result in death or serious
injury.
Caution indicates
CAUTION
!
a potentially haz-
ardous situation which, if not avoided,
MAY result in minor or moderate
injury.
Notice
NOTICE
!
indicates impor-
tant information, that if not followed,
may cause damage to equipment.

Unpacking

Remove the equipment and all parts
from the carton. The carton should
contain the following:
One (1) Pressure washer (pump,
engine, cart base)
One (1) Cart handle Assembly
One (1) Basket (not included with
all models)
One (1) Spray gun
One (1) Lance with nozzle
Five (5) Spray tips (not included
with all models)
One (1) High pressure hose
One (1) Pack of nuts, bolts,
manuals and Chemical Suction
Tube with Filter
If any parts are missing, DO NOT
return unit to the retailer. Know
model number (located on serial num-
ber tag on frame) and call 1-800-330-
0712 for replacement.
After unpacking the product, inspect
carefully for any damage that may
have occurred during transit. Make
www.chpower.com
sure to tighten fittings, bolts, etc.,
before putting unit into service.
Do not operate
WARNING
!
unit if damaged
during shipping, handling or use.
Damage could result in bursting and
cause injury or property damage.
See Product Manual for
General Safety Information

Assembly

1. Slide handle over legs and secure
with bolts provided.
2. Insert removable spray tips and
rubber grommets into holes pro-
vided on frame (if applicable).
3. Connect the clear plastic chemical
suction tube with filter to chemical
injector hose barb on the pump.
4. Connect the high-pressure hose to
the pump outlet.
5. Connect the high-pressure hose to
the gun.
6. Attach lance with nozzle to the
gun.
Pump outlet
Figure 1 - Pump hook up
2
Start Up
ALWAYS use this start up procedure to
ensure that the unit is started safely
and properly.
CAUTION
!
sure washer, thaw in a warm room
before starting. DO NOT pour hot
water on or into the pump; internal
parts will be damaged.
TRIGGER SAFETY LATCH
In the engaged position, the trigger
safety latch prevents the gun from
being triggered accidentally. Push
latch fully down to engage (See Figure
2). Always engage trigger safety latch
when unit is not in use.
Figure 2 - Trigger Lock
1. Check oil levels. Add oil as necessary.
NOTE: Some units are equipped with a
low-oil sensor that shuts engine off if
oil level falls below a certain level. If
Chemical
unit stops unexpectedly, check both oil
injector
and fuel levels. Check oil level each
hose barb
time unit is refueled.
2. Check fuel level.
Pump inlet
WARNING
!
Refueling a hot engine could cause a
fire. Use only fresh, clean regular or
unleaded gasoline. Close the fuel
shutoff valve during refueling.
3. Attach garden hose to inlet side of
pump and connect to water supply.
Hose should have an I.D. of 5/8" and
not be longer than 50 ft. (15 M).
If water has
frozen in the pres-
Engaged
Disengaged
DO NOT refuel a
hot engine.