AirKing Seville Serie Manual De Operación página 2

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

INSTALLATION INSTRUCTIONS
CAUTION:
MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL
BEFORE STARTING INSTALLATION.
SECTION 1
Preparing the Range Hood
1.
Unpack hood from the carton and confirm that all pieces are present. In
addition to the range hood you should have:
1 - Package containing:
1 - duct collar
4 - #6 blunt tip screws
4 - 4 x 15 mm mounting screws
1 - wire compartment cover
SEV24 models: 2 - Aluminum Grease Filters (shipped installed)
SEV28 models: 3 - Aluminum Grease Filters (shipped installed)
SEV30 models: 3 - Aluminum Grease Filters (shipped installed)
2 -50 watt Halogen lamps
1 - Instruction/Safety Sheet
NOTE: Some hoods may be shipped with a protective plastic adhered to the
underside of the unit. It is recommended to leave this in place during installation
to protect it from scratching. Remove when the installation is complete.
SECTION 2
Installing the Range Hood
CAUTION:
MAKE SURE POWER IS SWITCHED OFF AT SERVICE PANEL
BEFORE STARTING INSTALLATION.
CAUTION:
WHEN CUTTING OR DRILLING INTO WALL DO NOT DAMAGE
ELECTRICAL WIRING AND OTHER HIDDEN UTILITIES.
1.
Cut an appropriate size hole into the cabinet or canopy the power unit will
be mounted into (Figure 1):
SEV24 models: 18" wide by 10" deep.
SEV28 models: 28" wide by 10" deep.
SEV30 models: 30" wide by 10" deep
18" or 30"
Figure 1
NOTE: The hood must be mounted a minimum of 24" and a maximum of 36" from
the cooking surface.
NOTE: If you will not have access to the ducting or wiring once the hood is installed
into the cabinet or canopy, make the ducting and electrical connections at this
point by referring to the SECTION 3 and SECTION 4 of this instruction sheet.
NOTE: If an optional hood liner is being utilized, install at this point according
to the instructions included with the liner.
2.
Insert the power unit into the hole and secure in place using the four
provided 4 x 15 mm mounting screws (Figure 2).
Figure 2
6728012 Rev. B 5-09
CAUTION:
POWER UNIT TO IS CAPABLE OF SUPPORTING THE WEIGHT OF THE UNIT.
OTHERWISE YOU WILL NEED TO REINFORCE THE AREA.
SECTION 3
Ducting
CAUTION:
BUILDING CODES.
WARNING:
1.
Install the included duct collar to the hood with two of the provided #6
blunt tip screws (Figure 3).
Figure 3
2.
Connect the ducting to the duct collar and secure in place using tape to
seal all joints (Figure 3).
NOTE: The duct connector is 5.8" in diameter (for 6" round ducting) and the
center is located 3-3/16" inches from the back wall.
CAUTION:
WALL OR ROOF CAP.
SECTION 4
Wiring
CAUTION:
ACCORDANCE WITH LOCAL CODES, ORDINANCES, OR NATIONAL ELECTRICAL
10"
CODE. IF YOU ARE UNFAMILIAR WITH METHODS OF INSTALLING ELECTRICAL
WIRING, SECURE THE SERVICES OF A QUALIFIED ELECTRICIAN.
1.
Examine the wire compartment cover and select the most convenient wire
entrance and remove the knock out. Feed the supply wire through the opening
and install an appropriate strain relief. Connect the white wire from the
power unit to the white wire from the supply. Connect the black wire from
the power unit to the black wire of the supply. Connect the ground wire from
the home (green or bare) to the ground wire of the power unit (green or
green/yellow). Use approved methods for all connections (Figure 4).
Figure 4
www.airkinglimited.com
MAKE SURE THE SURFACE YOU ARE MOUNTING THE
ALL DUCTING MUST COMPLY WITH LOCAL AND NATIONAL
TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
Duct Collar
ALWAYS DUCT THE FAN TO THE OUTSIDE THROUGH A
ALL ELECTRICAL CONNECTIONS MUST BE MADE IN
Supply from home
Hot (Black)
Ground
From Hood
Ducting
Power Unit
White
2 of 12

Publicidad

Tabla de contenido
loading

Tabla de contenido