General Safety Rules; Work Area; Electrical Safety; Personal Safety - Hilti WSR 650-A Manual De Instrucciones

2. General safety rules

2.1 WARNING!
READ AND UNDERSTAND ALL INSTRUCTIONS
Failure to follow all instructions listed below, may result
en
in electric shock, fire and/or serious personal injury.
SAVE THESE INSTRUCTIONS.

2.2 Work Area

Keep your work area clean and well lit.
Cluttered benches and dark areas invite accidents.
Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases,
or dust.
Power tools create sparks which may ignite the dust or
fumes.
Keep bystanders, children, and visitors away while
operating a power tool.
Distractions can cause you to lose control.

2.3 Electrical safety

A battery operated tool with integral batteries or a se-
parate battery pack must be recharged only with the
specified charger for the battery.
A charger that may be suitable for one type of battery
may create a risk of fire when used with another battery.
Use battery operated tool only with specifically des-
ignated battery pack.
Use of any other batteries may create a risk of fire.

2.4 Personal safety

Stay alert, watch what you are doing, and use com-
mon sense when operating a power tool. Do not use
tool while tired or under the influence of drugs, alco-
hol, or medication.
A moment of inattention while operating power tools
may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewel-
ry. Contain long hair. Keep your hair, clothing, and
gloves away from moving parts.
Loose clothes, jewelry, or long hair can be caught in
moving parts.
Avoid accidental starting. Be sure switch is in the
locked or off position before inserting battery pack.
Carrying tools with your finger on the switch or insert-
ing the battery pack into a tool with the switch on invites
accidents.
Remove adjusting keys or wrenches before turning
the tool on.
A wrench or a key that is left attached to a rotating part
of the tool may result in personal injury.
2
Printed: 07.07.2013 | Doc-Nr: PUB / 5071405 / 000 / 00
Do not overreach. Keep proper footing and balance at
all times.
Proper footing and balance enable better control of the
tool in unexpected situations.
Use safety equipment. Always wear eye protection.
Dust mask, non-skid safety shoes or hearing protection
must be used for appropriate conditions.
2.5 Tool Use and Care
Use clamps or other practical way to secure and sup-
port the workpiece to a stable platform.
Holding the work by hand or against your body is unsta-
ble and may lead to loss of control.
Do not force tool. Use the correct tool for your application.
The correct tool will do the job better and safer at the
rate for which it is designed.
Do not use tool if switch does not turn it on or off.
A tool that cannot be controlled with the switch is dan-
gerous and must be repaired.
Disconnect battery pack from tool or place the switch
in the locked or off position before making any adjust-
ments, changing accessories, or storing the tool.
Such preventive safety measures reduce the risk of start-
ing the tool accidentally.
Store idle tools out of reach of children and other
untrained persons.
Tools are dangerous in the hands of untrained users.
When battery pack is not in use, keep it away from
other metal objects like: paper clips, coins, keys, nails,
screws, or other small metal objects that can make a
connection from one terminal to another.
Shorting the battery terminals together may cause sparks,
burns, or a fire.
Maintain tools with care. Keep cutting tools sharp and
clean.
Properly maintained insert tools with sharp cutting edge
are less likely to bind and are easier to control.
Check for misalignment or binding of moving parts,
breakage of parts, and any other condition that may
affect the tool's operation. If damaged, have the tool
serviced before using.
Many accidents are caused by poorly maintained tools.
Use only accessories that are recommended by the
manufacturer for your model.
Accessories that may be suitable for one tool may cre-
ate a risk of injury when used on another tool.
2.6 Service
Tool service must be performed only by qualified repair
personnel.