Tommee Tippee closer to nature perfect prep machine Inctrucciones De Uso página 16

WARNING LIGHTS ACTION BUTTONS
CHANGE
J
FILTER
CLEANING
O
MODE
WATER TANK
K
HOT
WATER LEVEL
L
LOW
DE-CALC /
M
DE-SCALE
CLEANING
N
MODE
SET UP
As with any other method of making up a feed, it's essential that good hygiene practices are observed in the use
and maintenance of your Perfect Prep machine. Ensure your hands and all surfaces that come in to contact with
the machine and its components are clean, and that the unit is away from direct sunlight and heat sources.
REGULAR CLEANING: For hygiene and safety reasons you should clean your unit on a regular basis. We recommend you carry
this out at least every 4 weeks, whenever you replace your filter or if the machine has been unused for a period of 7 days.
1 2 3
1 2 3
Place a container under the Plug in the unit, the tank empty Fill the water tank with
dispenser spout to capture the water warning light will illuminate. boiled water.
used to clean the system (ideally at
least 1.8 litre capacity).
5 6 7
5 6 7
Press the cleaning mode button and Allow the cycle to fully complete with The tank empty warning light will
hold for 2 seconds. The cleaning boiled water dispensing into the illuminate once the water has
mode light will illuminate. container that you placed underneath flushed through the system.
during step 1.
Handling the filter
9a
by the top only:
• Remove the filter from the
packaging
• Remove sticker from the top of filter
• Fill a bowl with cold tap water
• Fully submerge the filter in the water
• Gently agitate until the bubbles stop
Without removing the hopper from the machine and still holding the filter
by the top, place the filter in the hopper, ensuring it locks in to place.
FILTER
P
VOLUME
RESET
DE-CALC /
Q
DE-SCALE
15
12
FILTER
VOLUME
RESET
Press the filter volume reset button
for 2 seconds to clear the memory.
4
4
Before each use you must ensure that your water tank is above the minimum fill mark.
Always use cold water when filling the water tank, other than when cleaning.
freshly Wait for the tank empty warning
light to go out. The water tank hot
light will illuminate.
8
8
Check the water level and
regularly top up when necessary
with cold water. When filling the
tank with water, ensure the hopper
is in place.
Discard the contents from the
container used and place it back
under the dispenser spout.
11
10 11
9b
Fill the hopper with cold water. Wait for the tank empty warning
light to go out.
12 13 14
13 14 15
Set the dial to 4oz with container The appliance will dispense an Press the start/stop button again.
under the dispenser spout. amount of hot water. A green light will flash and an amount
Press the start/stop button. A red of water will be dispensed to finish
light will flash. the cycle. Discard the contents of the
container. Fit the bottle stand.
Your machine is now ready to use.
2. USAGE
1 2 3
Turn the dial to select the feed size Position your sterilised bottle under Press the start/stop button.
you require (4fl oz –11fl oz). the spout. Adjust bottle stand if A red light will flash and a volume
necessary (bottle neck should sit of hot water is dispensed into your
close to the spout). bottle.
4 5 6
8
The light will change to solid red Carefully remove the bottle from the Screw the sterilised milk storage lid
and there will be a double beep to stand and measure the correct onto the bottle and ensure that the
indicate the end of the first stage. number of formula scoops into the lid is tight. Be careful when handling
You will need to make up your feed bottle. hot liquid.
within 2 minutes.
10
9
Remove the milk storage lid and Press the start/stop button again. Wait whilst the remainder of water is
replace your bottle onto the bottle The red light will go out and the dispensed. Once completed, there
stand. green light will flash. If this button is will be a double beep and the green
not pressed within 2 minutes of the light will change to solid.
hot water being dispensed a long
beep will sound. If the alarm sounds
you should discard the feed and
repeat the process from step 1.
12 13
HOW TO KEEP THE TANK COOL
12 13
The Perfect Prep should be kept in a cool dry location,
avoiding direct sunlight and keeping away from warm
appliances. This is recommended to avoid the water tank
temperature getting too warm.
Don't worry if your temperature light does illuminate, as we
have some tips for you:
Flush your cold tap for 10 seconds before filling the
1
water tank.
For your child's safety always check Your bottle is now ready to serve.
food temperature before feeding by Make sure you discard any
Regularly top up with cold water rather than letting a
2
testing on a sensitive part of your unwanted feed as per the formula
full tank stand and warm for long periods of time.
skin. manufacturer's recommendation.
3 Keep a cold jug of tap water in the fridge ready to top
up the tank.
HOW TO STOP THE PERFECT PREP™ MACHINE
If at any point you need to stop the Perfect Prep machine you can do so by pressing the start/stop button. The pump may
continue to run for a few seconds and the green light will illuminate to show that the process has ended.
It will not be possible to restart the machine for 20 seconds. If you have to stop the Perfect Prep machine, please discard of
any incomplete feed.
7
Shake well until the formula powder
has dissolved.
11
11
Always check that the amount
dispensed is consistent with the
size of feed you have selected on
the dial (by adding formula, your
feed will appear larger than the feed
size chosen). Add the sterilised teat,
screw ring and hood and shake.