Publicidad
Idiomas disponibles
Idiomas disponibles
Always wear SAFETY GLASSES
when installing hitch
Scan for step by step
PHOTO installation
instruction or visit
Existing Weld Nuts
http://www.cequentgro
up.com/qr-product.aspx
Small Block
①
②
Large
block
Pull Wire
See Step 3
⑥
③
①
⑤
Pull Wire blocks
③
④
1. Remove the fascia door, if present.
2. Feed the carriage bolt and large block thru slots on bottom of frame rails using the pull wire, as shown Figure 3
3. Raise the hitch into position; lifting the bumper mounting bracket over the fascia (where needed). Secure with M12 bolts and conical washers into
the existing weld nuts, being careful not to push the bolts into the frame, as shown Figure 1.
4. Feed conical washer over pull wire, using the washer to hold the bolt in place remove the pull wires and attach the hex nut. Hand tighten all bolts.
5. On vehicles without existing weldnuts in the bumper: Pull carriage bolts and small blocks thru end of the bumper and feed through the bumper mounting bracket using the pull wire.
Attach conical washer and nut. As shown Figure 1.
On vehicle with existing weldnuts in bumper: Install the M12 bolts and conical washer through the bumper mounting bracket into the existing
weld nuts in the bumper, as shown Figure 2.
6. Tighten all 1/2-13 GR5 fastener with torque wrench to 75 Lb.-Ft. (102 N*M). Tighten all M12 CL10.9 fasteners with torque wrench to 92 Lb.-Ft. (125 N*M)
7. Replace the fascia door on the 2005-2015 Equinox. For 2016 and newer see Figure 4 for optional trimming. (Obtain owners permission prior to trimming).
For all other models return fascia door to owner.
Note: Due to different configuration of the vehicle there will be extra hardware left over.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or
ball which has been damaged should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2016 Cequent™ Performance Products, Inc. -
Installation Instructions
PART NUMBERS: 76028, 84028
Frame
Fasteners typical
rail
both sides.
Bumper
Mounting
Bracket
Figure 1.
③
⑦
⑤
Existing Weld Nuts
Proper torque is needed to keep the hitch secure to the vehicle when towing.
Printed in Mexico
Center of fascia door
3" [76.2mm]
3/4" [19 mm]
3" [76.2 mm]
Bumper
Figure 4.
Optional Fascia
trimming for
2016 and newer
Chevrolet Equinox
Existing
Weldnut
Rear
Figure 2.
Sheet 3 of 15
Fastener Kit : 76028F
①
Qty. (4)
Carriage bolt
½-13 x 1.50 GR5
②
Qty. (2)
Spacer
.250 x 1.50 x3.00
③
Qty. (8)
Conical washer
6"
½''
[152.4]
④
Qty. (4)
Het Nut
½ -13 GR2
⑤
Qty. (6)
Bolt
M12x1.75x45 CL10.9
⑥
Qty. (2)
Spacer
Both side
.250 x 1.50 x 2.0
⑦
Qty. (4)
Pull wire
½-13
Example of pull wire procedure
(Conical Washer)
Teeth side
against hitch
Figure 3
76028NP
3-30-16
Rev. A
Publicidad
