Husqvarna 594 73 07-01 Manual De Instalación página 6

REMOVAL & INSTALLATION
INSTALL ANTI-SWAY BAR
FOR TRACTORS WITH 20" DIAMETER REAR
WHEELS ONLY (KIT# 594 73 07-01)
• If you have replacement deck kit model 594 74 20-01
for lawn tires with 20" diameter rear tires, then your kit
includes a new Anti-Sway Bar (Part# 532 44 32-37)
for installation. Install using the new washer and lock
pin provided.
FOR TRACTORS WITH 23" DIAMETER REAR
WHEELS ONLY (KIT# 594 73 07-01)
• Reinstall original Anti-Sway Bar from right side of
mower on tractors with 23" tires.
ANTI-SWAY BAR (S)
TOWARDS
TRANSAXLE
90° END
TO LEVEL MOWER (See Figs. 9 - 10)
Ensure tires are properly inflated to the PSI shown on tires.
If tires are over or under inflated, it may affect the appear-
ance of your lawn and lead you to think the mower is not
adjusted properly.
VISUAL SIDE-TO-SIDE ADJUSTMENT (See Fig. 9)
• With all tires properly inflated and if your lawn appears
unevenly cut, determine which side of mower is cutting
lower.
NOTE: As desired, you can raise the low side of mower
or lower the high side.
• Go to side of mower you wish to adjust.
• With a 3/4" or adjustable wrench, turn lift link adjustment
nut (A) to the left to lower the mower, or, to the right to
raise the mower.
TURN NUT RIGHT
TO RAISE MOWER
NOTE: Each full turn of adjustment nut will change mower
height about 3/16" (4,7 mm).
• Test your adjustment by mowing some uncut grass and
visually checking the appearance. Readjust, if neces-
sary, until you are satisfied with the results.
TOWARDS
MOWER DECK
INTEGRATED WASHER END
Fig. 8
A
TURN NUT LEFT
TO LOWER MOWER
Fig. 9
PRECISION SIDE-TO-SIDE ADJUSTMENT (See Fig. 10)
• With all tires properly inflated, park tractor on level
ground or driveway.
CAUTION: Blades are sharp. Protect
your hands with gloves and/or wrap
blade with heavy cloth.
• Raise mower to its highest position.
• At both sides of mower, position blade at side and mea-
sure the distance (A) from bottom edge of blade to the
ground. The distance should be the same on both sides.
• If adjustment is necessary, see steps in Visual Adjust-
ment instructions above.
• Recheck measurements, adjust if necessary until both
sides are equal.
A
FRONT-TO-BACK ADJUSTMENT (See Figs. 11 & 12)
IMPORTANT: Deck must be level side-to-side.
To obtain the best cutting re sults, the mower blades should
be adjusted so the front tip is 1/8" to 1/2" (3,1 to 12,7 mm)
lower than the rear tip when the mower is in its highest
position.
CAUTION: Blades are sharp. Protect
your hands with gloves and/or wrap
blade with heavy cloth.
• Raise mower to highest position.
• Position any blade so the tip is pointing straight forward.
Measure distance (B) to the ground at front and rear tip
of the blade.
B
• If front tip of blade is not 1/8" to 1/2" (3,1 to 12,7 mm)
lower than the rear tip, go to the front of tractor.
• With an 11/16" or adjustable wrench, loosen jam nut A
several turns to clear adjustment nut B.
• With a 3/4" or adjustable wrench, turn front link adjust-
ment nut (B) clockwise
mower, or, counterclockwise
front mower.
6
A
Fig. 10
B
Fig. 11
(tighten) to raise the front of
( )
(loosen) to lower the
( )