Publicidad
Idiomas disponibles
Idiomas disponibles
27.
Nur originale Ersatzteile verwenden.
28.
Die Maschine nur zum Wechsel der Kohlebürsten
demontieren.
29.
Beim Transport und Handling von Kernborngeräten
vom Lagerort zum Einsatzort sind die in dem Land,
in dem die Kernborngeräte eingesetzt werden,
geltenden Arbeitsschutzvorschriften zu beachten.
SICHERHEITSHINWEISE FÜR DIE NUTZUNG DES GERÄTES
1.
Augen mit Schutzbrille schützen.
2.
Tragen Sie eine Staubmaske.
3.
Gehörschutz verwenden.
4.
Auf die richtige Einstellung des Handgriffs achten.
5.
Es
wird
empfohlen
den
Seitenhandgriff
verwenden.
6.
Sichere Arbeit hängt von der Körperhaltung ab.
7.
Bei der Arbeit in der Höhe auf Personen und
Gegenstände auf tiefer gelegenen Flächen achten.
8.
Bei der Arbeit mit dem Gerät immer Sicherheitsschuhe
tragen.
Werden die Anweisungen und Sicherheitshinweise
verletzt kann das zu ernsthaften Körperverletzungen
oder zum Tod führen!
4
zu
Rev. 14.05.2020
U S E R M A N U A L
LEGEND
The operation manual must be read carefully.
Never dispose of electrical equipment together
with household waste.
This machine conforms to CE declarations.
Safety goggles must be used.
Ear protection must be used.
Safety mask must be used.
Protective footwear must be used.
Attention! Wear protective gloves.
ATTENTION! Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in serious injury or even
death.
The terms "device" or "product" are used in the warnings
and instructions to refer to DIAMOND DRILLING MACHINE.
SAFETY INSTRUCTIONS
1.
Keep the work area clean. Cluttered areas can cause
injuries.
2.
Consider the work area environment before starting
to work. Don't expose power tools to rain or wet soil.
Don't use power tools in damp or wet locations. The
work area should be well secured. Don't use the tool
in the presence of flammable liquids or gases. Power
tools produce sparks during normal operation or
when switching ON/OFF. Never use power tools in
dangerous sites containing lacquer, paint, benzene,
thinner, gasoline, gases, adhesive agents, and other
materials which are combustible or explosive.
3.
Provide sufficient protection against electric shock.
Prevent body contact with grounded surfaces,
for example: pipes, radiators, ranges, refrigerator
enclosures.
4.
Keep children and third parties away from the work
area.
5.
Store unused tools. When not in use, tools should be
stored in dry and high or locked-up places out of the
reach of children.
6.
Do not overload the machine! To ensure an optimum
performance and the safety of the machine, only use
it within the set parameters.
7.
Use only suitable tools. Don't use small tools or
attachments. Don't use tools for not intended
purposes. For example: don't use circular saws for
cutting tree limbs or logs
8.
Dress appropriately. Do not wear loose clothing
or jewellery. They can get caught in the moving
parts. Rubber gloves and non-skid footwear are
recommended when working outdoors. Wear
protective hair covering to contain long hair.
9.
Use safety glasses. Also use a face or dust mask if the
cutting operation is dusty.
10.
Do not damage the connection cable. Never carry
the tool by the cord or yank the cord to disconnect
it from the power source. Keep the cord away from
heat and oil sources and sharp edges.
11.
Secure the work area. It is recommended to use
clamps or a vice for fixation. Please pay special
attention to your hands when operating the machine.
Rev. 14.05.2020
12.
Do not overreach yourself. Keep proper footing and
balance at all times.
13.
Hold the machine firmly with both hands. When
using the machine, hold it by the handles provided
with the machine.
14.
Maintain tools with care. Keep tools clean for a better
and safer performance. Follow the instructions for
changing accessories. Inspect the extension cords
periodically and replace if damaged. Keep handles
dry, clean, and free from oil and grease.
15.
Switch off the machine and disconnect the cable
before
performing
maintenance
or
changing
accessories.
16.
Remove adjusting keys and wrenches. Always make
sure that keys and adjusting wrenches are removed
from the tool before turning it on.
17.
Avoid unintentional starting. Don't carry a plugged-
in tool with your fingers on the switch. Be sure the
tool is switched off when plugging it in.
18.
During outdoor work use extension cords intended
for outdoor use.
19.
Stay alert when operating the machine. Do not
operate the tool when you are tired.
20.
Check damaged parts. Before further use of the
tool, any part of the casing or other parts that are
damaged should be carefully checked to determine
if they will operate properly and perform their
intended function. Check for alignment of moving
parts, mounting, and any other conditions that
may affect its operation. A damaged part should
be properly repaired or replaced by an authorized
service centre unless otherwise indicated elsewhere
in this instruction manual. Defective switches should
be replaced by an authorized service centre. Do not
use the tool if the switch does not turn it on and off.
21.
Do not use power tools for applications other than
those specified in the instructions (other than that for
which it was designed).
22.
To ensure the designed operational integrity of
power tools, do not remove installed covers or
screws.
23.
Do not touch movable parts or accessories unless the
power source has been disconnected.
24.
Use your tool at a lower input load than specified
on the nameplate to increase working efficiency and
decrease the wearing out process.
25.
Do not wipe any plastic parts with solvents. Solvents
such as gasoline, thinner, benzene, alcohol, ammonia
and oil may damage and crack the plastic parts. Do
not wipe them with such solvents. Wipe the plastic
parts with a soft cloth lightly dampened with soapy
water.
26.
Consult an authorized service agent in the event of
power tool failure.
27.
Use only original replacement parts.
28.
This tool should only be disassembled for replacing
carbon brushes.
29.
When transporting and handling the diamond
drilling machine between the warehouse and the
destination, take into account the occupational
health and safety principles for manual transport
operations which apply in the country where the
device will be used.
5
Publicidad
