STAMOS S-LS-6 Manual De Instrucciones página 10

6. Setting the automatic (AUTO) or manual (MANUAL) SMD rework gun working
mode: switching between modes: press buttons (11) and (12) simultaneously
for about 3 seconds – „AUTO" or „MANUAL" flashes, set the desired working
mode by pressing buttons (11) and (12), device will enter into chosen mode
after a few seconds. In manual mode, SMD rework gun working continuously. In
automatic mode, SMD rework gun turns off when placed into the holder. Chosen
"AUTO" or "MANUAL" mode will be shown on the display.
7. Cold airflow setting: during normal work of the device, press the knob-button (1)
to enter into cold airflow mode. Display will show "COL" and device starts coo-
ling the SMD rework gun.
8. After work, the SMD rework gun should be placed into the holder. Turn off the
SMD rework by switch (5).
9. If the device is not used for a long time, it should be completely disconnected
from the power source.
Press buttons (12) and (14) simultaneously for about 3 seconds, the ⁰C or ⁰F will be
CHANGING THE TEMPERATURE UNIT (CELSIUS / FAHRENHEIT):
flashing on the display. Set the desired unit using buttons (12) and (14). Chosen unit
will be shown on the display.
MEMORY BUTTONS CH1, CH2, CH3.
Device is equipped with memory buttons for saving entered data CH1, CH2, CH3.
Each button can save any configuration of all working parameters of the device: sol-
dering iron temperature, SMD reworks gun temperature, working mode of the SMD
rework gun (AUTO or MANUAL), airflow volume, soldering iron sleep time, tempe-
rature unit.
When all needed parameters are entered, press the button CH1 or CH2 or CH3 for
approx. 3 seconds. After this time, the parameters will be stored under the button
which was pressed. Later, pressing this button will cause immediately operation of the
device with these stored parameters.
SETTING THE SOLDERING IRON AND SMD REWORK GUN TEM-
PERATURE COMPENSATION
Entering into temperature compensation setting mode: when both stations are tur-
ned on (switches 5 and 6 turned on), press simultaneously buttons (11) and (15) for
about 3 seconds. Both displays will show "00" and "SOLDERING" and "HOT AIR" will
be flashing. Using buttons (11) and (12) set the desired temperature compensation
for soldering iron. Using buttons (14) and (15) set the desired temperature compen-
sation for SMD rework gun. The range of the compensation is from -50 to +50⁰C.
After setting, device will remember entered parameters and starts working after ap-
prox. 5 seconds.
18
EN
GENERAL REMARKS
than 100 ⁰C, HOT AIR station is in stand by mode, HOT AIR gun is placed in the
1. If the display is showing the „---„ it means that the output temperature is lower
holder.
2. If the display is showing "S-E" it means that soldering iron is disconnected, and
HOT AIR gun is having problem with the heat sensor.
3. If the display is showing "F-1" it means that electric circuit of the fan is having
problem.
4. If the display is showing "F-2" it means that the fan is blocked.
5. When the device is being turned on, both soldering iron and HOT AIR gun
should be placed in their holders.
6. The outlet of the HOT AIR gun should be clean and free from any obstacles.
7. When using small nozzles, it should be remembered that the air flow should be
suitable to the diameter of the fixed nozzle. In order to avoid any HOT AIR gun
damages, too high air flow along with the high temperature mustn't be used for a
long period of time.
8. Depending on user's needs, different air flow settings may cause slight variations
in temperatures value. The minimum distance between the outlet of the HOT
AIR gun and the subject is 2 mm.
9. Good ventilation of the room in which the appliance is used must be provided.
In addition, the device should be placed in a location with good air circulation to
dissipate heat.
SAFETY ISSUES REMARKS
1. Nozzles should be installed without the use of excessive force, also do not use
the pliers or tweezers. Do not over tighten the mounting screws of the nozzle.
2. Tips and nozzles can be changed when the HOT AIR gun and the soldering iron
are completely cold.
3. It is forbidden to use the device near the flammable or combustible elements
and objects or at similar places. Tips and nozzles as well as the air coming out
of the HOT AIR gun have very high temperature, it is forbidden to touch these
elements as well as it is forbidden to put the hot air directly to face or body. This
can cause serious burns.
4. After long time of use, the outlet of HOT AIR gun may be covered with some
dust. The outlet should be cleaned on a regular basis in order to ensure undistur-
bed air flow.
5. Too high temperature of the soldering iron may be the cause of reduction of the
functionality of the soldering tips.
6. Soldering iron tip must be cleaned regularly using sponge and plate on a layer of
tin to prevent tips oxidation.
EN DE
19