Char-Broil 465640214 Guía Del Producto página 4

WARNING
Turn controls OFF and disconnect cylinder when not
in use.
Ignitor Lighting
READ INSTRUCTIONS BEFORE LIGHTING.
Do NOT lean over appliance while lighting.
1. Turn the control valve to the OFF position.
2. Connect LP gas cylinder.
3. Open the grill lid.
4. Turn the control knob to the HIGH position.
5. Press the ignitor button rapidly.
6. Once ignited, turn the control knob to the desired
setting.
7. If ignition does not occur in 5 seconds, turn the
burner control knob OFF , wait 5 minutes, and repeat
lighting procedure.
If ignition still does not occur, follow match-lighting
instructions.
CAUTION
If ignition does NOT occur in 5 seconds, turn
the control knob OFF, wait 5 minutes and repeat
the lighting procedure. If the burner does not
ignite with the valve open, gas will continue to
flow out of the burner and could accidently
ignite with risk of injury.
Match Lighting Instructions
Important! Raise lid to open position.
Attempting to light burner with lid closed may
cause an
explosion. Do not expose any part of your
body or clothing directly above cooking area
when lighting.
1. Read all instructions before lighting.
2. From the right side of the grill, place lighted
wooden match through lighter/ventilation
holes in right side of the grill.
3. While holding match next to the burner, turn
control knob to the HIGH position. Grill will
ignite.
4. If ignition does NOT occurs in 5 seconds,
turn the burner controls OFF, wait 5 minutes
and repeat the lighting procedure.
5. Observe burner flames through openings in
heat distribution plate. Make sure burner
ignites and stays lit on both sides.
6. Preheat grill for 10 minutes with lid closed.
Using control knob on Regulator/Valve,
adjust flame to desired height for cooking.
Turning Grill Off
Turn control knob to OFF position.
Disconnect LP cylinder.
Burner Flame Check
Light burner. Make sure burner stays lit while
rotating the control knob from HIGH to LOW.
Always check flame prior to each use.
High
Low
Ignitor Check
• Remove LP cylinder. Turn ignitor knob. "Click"
should be heard each time at electrode. See
"Troubleshooting" if no click or spark.
Before Your First Cookout
Leak test your grill. Light burner, check to make sure
it is lit. Close the lid and warm up 5 for 10 minutes.
Additional curing of paints and parts will produce an
odor only on first lighting.
CAUTION
SPIDER ALERT!
SPIDER AND WEBS
INSIDE BURNER
If your appliance is getting hard to light or the flame is
weak, check and clean the venturi's and burners.
Spiders or small insects are know to create
"flashback" problems by building nests and laying
eggs in the appliance venturi or burner obstructing
the flow of gas. The back-up gas can ignite behind
the control panel. This flashback can damage your
appliance and cause injury. To prevent flashbacks
and ensure good performance the burner and
venturi tube assembly should be removed and
cleaned when ever the appliance has been idle for
an extended period of time.
IF YOU EXPERIENCE THE FOLLOWING:
1. Smell gas.
2. Burner will not light.
3. A small yellow flame from burner (should be blue).
4. Fire coming from around or behind control knob.
STOP!
IMMEDIATELY TURN OFF GAS AT LP CYLINDER!
1. Wait for grill to cool.
2. Use a 12" pipe cleaner to clean out the burner tube.
4
General Grill Cleaning
Do not mistake brown or black accumulation of grease
and smoke for paint. Interiors of gas grills are not
painted at the factory (and should never be painted).
Apply a strong solution of detergent and water or use a
grill cleaner with scrub brush on insides of grill lid and
bottom. Rinse and allow to completely air dry. Do not
apply a caustic grill/oven cleaner to painted
surfaces.