Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
English
Work Surface
Mounting Wood Top
Process
1. Remove wood top work surface from packaging.
Assemble Backsplash to Wood Top
(Fig. K)
Items Needed
•
Backsplash (Qty: 1)
•
#14‑10 x 5/8" Hex Screw (Qty: 4)
•
27" Wide Unit (Qty: 4)
•
54" Wide Unit (Qty: 4)
•
3/8" Socket
•
3/8" Wrench
•
Socket Wrench
Process
1. Attach backsplash
12
#14‑10 x 5/8" hex screws
backsplash with the pre‑drilled holes in the back and
bottom of the top.
2. Wrench tighten all screws securely. Do not over tighten.
nOTE: Base cabinets are not as deep as floor cabinets. If you
are planning to place a base cabinet next to a floor cabinet,
decide if you want the base cabinet flush with the front of
the floor cabinet or if you want them pushed
back against the wall.
Mounting Wood Top to Base Cabinet Top
(Fig. L, M)
Items Needed
•
#14‑10 x 1" Hex Screw (Qty: 2)
•
26" Wide Unit (Qty: 2)
•
54" Wide Unit (Qty: 2)
•
3/8" Socket
•
3/8" Wrench
•
Socket Wrench
Process
nOTE: If mounting work surface to multiple cabinets, place
cabinets in position before mounting the work surface.
nOTE: If mounting work surface to a unit with drawers refer
to the Operator's Manual for that unit to remove top drawers.
This will provide access to the inside of top of unit.
1. Position work surface on the top of cabinet(s)
2. Wrench tighten all screws securely. Do not over tighten.
3. Reinstall drawers per base cabinet Operator's Manual,
if applicable.
Assembling the Leveling Feet (Fig. N)
Items Needed
•
Screw Leveler (Qty: 4)
1. Lay the floor/base cabinet on its back. Use packaging
material to protect the finish.
2. Install (4) Screw Levelers
8
to back of work surface
13
14
by aligning the holes in the
1
.
3. Return the cabinet to its upright position.
nOTE: Some adjustments may be necessary after cabinet
is in desired location.
OPERATION
Removing Drawers (Fig. O, P)
1. Empty the drawer.
2. Fully extend the drawer.
3. Push the right release slide lever down
left release slide lever
4. Pull out drawer to remove.
Leveling Foot Adjustment (Fig. Q)
Adjust leveling foot
screwdriver or 7/16 open end wrench as shown in Fig. Q.
Door Closure
Ensuring the cabinet is level (front to back) will result in
the correct alignment of the doors and proper function of
using
the magnetic door closure system.
MAINTENANCE (FIG. R)
•
Lubricate casters annually with high quality bearing
grease. Apply grease where shown.
•
Check the caster bolts annually for tightness.
•
Lubricate the slides with grease or equivalent (twice
annually). Apply grease where shown.
•
Lubricate lock with graphite annually.
•
Periodically the drawer fronts, drawer trim, and other
surfaces should be cleaned with a mild detergent
and water.
•
Auto wax will preserve the unit's luster finish. Apply the
wax as to a car. The wax will also help protect the unit
against scratches.
•
Grease and oil can be removed with most standard
cleaning fluids. For safety, use a nonflammable
cleaning fluid.
•
It is recommended that drawer liners are used to protect
the finish inside the drawers and to make the drawers
easier to clean. The drawer liners may be cleaned with
soap and water.
•
Corrosive materials should be cleaned up immediately to
minimize damage to any surfaces.
TEN YEAR WARRANTY
FOR TEN YEARS from the date of purchase, this product is
warranted against any defects in material or workmanship.
With proof of purchase, a defective part will be replaced free
of charge. If a replacement part is unavailable, the product
will be replaced with one of equal value.
For warranty coverage details to obtain free replacement,
visit the web page: www.craftsman.com/warranty
This warranty does not apply to a product that is damaged
or altered through transportation, misuse, abuse, corrosion,
accident, neglect, modification or mishandling, nor
does coverage apply if the product is ever attached to a
moving vehicle.
6
7
up.
1
to desired position with flat head
, then push the
Publicidad
Tabla de contenido
