Zoeller 292-0002 Instrucciones De Instalación página 3

RECOMMENDED INSTALLATION FOR ALL APPLICATIONS
1. lectrical wiring and protection must be in accordance with governing
electrical codes.
2. Install proper Zoeller unichec combination union and chec valve ,
preferably just above the basin to allow easy removal of the pump
for cleaning or repair. If high head or below cover installation is
re uired, use 30 0164 on 1
on 3 pipe.
3. ll installations re uire a basin cover to prevent debris from falling into
the basin and to prevent injury.
4. hen a nichec is installed, drill a
pipe even with the top of the pump. NOTE: THE HOLE MUST ALSO
BE BELOW THE BASIN COVER AND CLEANED PERIODICALLY.
igh ead unit see Caution on front page .
visible from this hole when pump is operating.
5. Securely tape or clamp power cord to discharge pipe, clear of the oat
mechanism s .
6. se a discharge pipe e uivalent in diameter to the pump s discharge.
See FM0531, FM0732, FM1597 & FM1420 for
alarms, controls & junction bo es
1
10
2
12
13
3
MINIMUM
18"x24" BASIN
(457 mm X 610 mm)
5
LARGER DEPTHS
MAY BE
6
REQUIRED.
4
7
8
14
9
4" (10 cm) OF GRAVEL
IC D IN INS
All installations must comply with all applicable electrical and plumbing codes, including, but not limited to, National Electrical Code, local, regional, and/or state plumbing
codes, etc. Not intended for use in hazardous locations.
On some installations, it may be desirable
to install an independent hanger for the
level control switches to avoid possible
hang ups on the pumps, piping, valves,
etc. Float hangers are available from
Zoeller Company on Catalog Sheet
FM0526 or can be fabricated from stan
dard pipe and ttings.
pipe, 30 0152 on 2 pipe and 30 0160
/
diameter hole in the discharge
3
16
ater stream will be
lways refer to
FM0551 and/or
SS M recom
mended sewage
pump installation
and maintenance.
TURN
ON
TURN
OFF
ION IC S
Suggested Methods Of Float Installation
TYPICAL FLOAT HANGER ON STEEL COVER PITS
PEA GRAVEL
© Copyright 2015 Zoeller
7. asin must be in accordance with governing codes and speci cations.
8. ump must be level and oat mechanism s clear of sides of basin
before starting pump.
9. asin must be clean and free of debris after installation.
10. ate valve, shut off valve, or ball valve to be supplied by installer and
installed according to any and all codes.
11. ocate oat switches as shown in s etches. he best place for the off
point is above the motor housing and positioned 180 from the inlet.
Never put off point below discharge on pump
12. as tight seals are re uired to contain gases and odors.
13. ent gases and odors to the atmosphere through vent pipe.
14. Optional pump stand /N 10 2421 eliminates the need for bloc s or
bric s under the pump. For use with ef uent and dewatering pumps only.
15. Optional watertight control bo available, see FM1597 for details.
16. For proper spacing of On
national standards and guidelines.
17. Optional septic tan risers for easy access to pump, controls and lters.
See FM0531, FM0732, FM1597 & FM1420
for alarms, controls & junction bo es
4" (100 mm)
OF GRAVEL
INS ION
ACCESS COVER
STANDARD PIPE
FLANGE
PVC OR LIGHT WEIGHT
STAINLESS STEEL PIPE
®
Co. All rights reserved.
3
Off switches refer to local or
WW1
EFFLUENT
FILTER
IC FF N INS ION
TYPICAL FLOAT HANGER ON CONCRETE PITS
OR SEPTIC TANK RISERS
10-1457 FLOAT TREE
WITH 3 FLOATS SHOWN
TYPICAL FLOAT HANGER ON CONCRETE PITS
OR SEPTIC TANK RISERS