Important Safety Instructions; Technical Specifications - Televes T.0X Serie Guía Rápida

M/N TWIN MODULATOR

Important safety instructions

General installation conditions
• Before handling or connecting the equipment, please read this manual.
• In order to reduce the risk of fi re or electric shock, do not expose the equipment
to rain or moisture.
• Do not take the cover off the equipment without disconnecting it from the
mains.
• Do not obstruct the equipment's ventilation system.
• Please allow air circulation around the equipment.
• The equipment must not come into contact with water or even be splashed
by liquids. Do not place containers with water on or near the equipment if it is
not adequately protected.
• Do not place the equipment near sources of heat or in excessively moisture
conditions.
• Do not place the equipment where it may be aff ected by strong vibrations or
knocks.
• This symbol indicates that the equipment complies with the
requirements of CE mark.
NOTE: You have a complete User Guide on our website:
www.televes.com.
Links available at the end of this guide
Technical specifi cations
Bandwidth
Input level (75 ohm)
Video
Modulation depth
Diff erencial gain
Bandwidth
Impedance
Audio
Pre-emphasis
Deviation (1KHz/1.7Vpp input)
Output frequency
Impedance
Output level
Regulation margin
RF output Level stability
Pa/Pv distance
IF frequency
Frequency steps
C/N (5MHz)
Power supply
General
Consumption 24V
- Each output of the Power Supply Unit can power up to 4 modules
- The technical characteristics described are defi ned for a maximum ambient temperature of 45°C (113ºF). Forced ventilation is used for higher temperatures.
Inputs/Outputs/Connections description
The unit (Fig. 1) is provided with:
1. RF output + 2 CH TV (module A and module B)
2. Powering BUS connectors
3. Status LED
4. Control BUS connectors
5. Audio / video input signal connector (module A and module B)
6. Programmer / PC connector
Introduction
The TWIN unit features two A/V inputs (modules A and B) which generate
two independent output channels.
The A/V inputs for each module (A and B) are modulated according to the TV
standard in an IF of 38.9 MHz.
The modulated IF signal is converted to any channel or frequency between 46
and 862 MHz and then, once fi ltered, it is amplifi ed to achieve the specifi ed
output level.
The module confi guration can be done using the universal programmer
(Ref.7134) or the TSuite software for PC.
Possibility of local/remote control and monitoring (IP / GSM) for modules
thanks to the headend management unit (CDC) ref. 5559/555901.
MHz 0.00005 ... 4.2
Vpp 1
% 68.5 ... 82.5
% < 4
KHz 0.04 ... 15
ohm 10000
μs 50
program. (see table)
MHz 46 ... 862
ohm 75
dBmV 34 ± 5
dB > 15
dB ± 3
-12, -14, -16, -18 (prog.)
MHz 38.9
KHz 250 (prog.)
dB > 56
V 24
mA 300
Diff erencial phase
Chroma/luma Delay
Chroma/luma Delay
Flatness
S/N ratio
Flatness
Input level
Distortion (1KHz dev. ± 30KHz)
Audio carrier precision
Video carrier stability
Carrier ratio
Band spurious level
46 ... 862MHz
Protection index
6
° < 4
ns < 100
dB > 52
dB < +1
dB > 45
dB < ±1
dBm >-15 <7
% < 1
VHF < 25
KHz
UHF < 50
VHF < 15
KHz
UHF < 30
MHz 4.5
55 min.
dBc
> 60 typ
IP20