Publicidad
Idiomas disponibles
Idiomas disponibles
11. Connect the hose to the machine's intake with the
quick-connect adapter (not included). (Fig. E)
12. Open the water valve of the installation and adjust the
water flow with the valve on the machine.
13. To close water flow, turn the value to the perpendicular
position and close the installation's water valve. (Fig.
D-12)
WARNING! Before starting, make sure that the dust
cover is in its proper position. If not, the functioning of
the water feed system could be affected, reducing the
blade cooling capacity.
Connection of the suction system:
Direct connection with RUBI vacuum
14. The AS-30 PRO vacuum can be connected directly to
the tool without the need for an adapter.
15. Remove the suction intake and insert the vacuum
nozzle into the machine's air intake. (Fig. F)
Connection with an adapter
16. To connect vacuums not specified in the previous
section, a universal adapter (included) must be used.
17. Remove the suction intake and insert the universal
adapter into the machine's air intake. Then, the hose
of the vacuum that you wish to use. (Fig. G)
18. The diameters that are compatible with the use of the
universal adapter are Ø37, 42 and 50 mm.
¡WARNING! Check that your vacuum cleaner has a
filter for wet suction, and that is properly mounted.
Otherwise, don't use vacuum cleaner together with
the open water supply.
Adjusting the cutting depth:
19. Loosen the depth adjustment lever (counter-
clockwise) to release the position of the machine.
20. Adjust to the desired cutting depth using the depth
reference scale, and tighten the lever (clockwise) to
secure the position of the head. (Fig. H)
Adjusting the cutting angle:
21. The mitre cutting mechanism allows you to adjust the
cutter angle from 0 to 45°. For more precise cutting,
use the marks on the chassis support.
22. Turn the lever counter-clockwise for mitred cuts. The
system will be unlocked to allow adjustment. (Fig. I-9)
23. Turn the cutter head to the desired cutting angle. For
greater precision, you can use the angle marks on the
front of the frame, lining up the mark for the desired
angle with the pointer at the end. (Fig. I)
24. Once the cutting angle has been set, turn the lever
clockwise to lock the cutting position.
NOTE: for a square cut, turn the cutter head to the
0° position, so that the blade is perpendicular to the
piece being cut.
WARNING! When adjusting the cutter, make sure
that the side guard pivots automatically. When you
are finished cutting, put the side guard in its original
position. (Fig. I-8)
Slim Cutter rail system:
Using the TC-125 quick-set clamps
25. The SLIM SYSTEM guide system, included in the TC-
125 KIT, allows you to use the cutter to make precise,
square and clean cuts, while at the same time
protecting the surface of the ceramic being worked
against damage.
26. The TC-125 KIT includes 2 quick-set clamps to hold the
guide profile to the work piece. Using these elements
guarantees that the profile is firmly secured to the
English
TRANSLATION OF THE ORIGINAL
27. To install the clamps, insert the rod into the guide rail
28. If the work piece is long, the use of suction cups is
29. To optimise the cutting zone, the suction cups must
30. To install the suction cups, insert the anchor nut into
31. When the suction cup is in the correct position, secure
32. 32. For the installation of the SLIM CUTTER guides,
33. Insert the machine through one of the ends of the
34. If you notice that there is some play between the
Preliminary checks:
35. Verify that the voltage of the power supply matches
36. 230 V machines may also be connected to 210V /
37. Before using the machine, check for any worn,
38. If the blade is installed incorrectly and is working in
39. Use only the blade diameters indicated in this manual,
3.2 Staring the machine
PRCD unit (Electronic overload protection):
40. Plug the PRCD unit into an electrical outlet. The green
41. Press the "TEST" button. The indicator light should go
work piece, allowing for a safe cutting operation.
of the profile as shown in the image. Then adjust the
height if the handle of the clamp and secure it to the
work zone. (Fig. J)
Use of SLIM CUTTER suction cups
WARNING! Make sure to clean the surface of the work
piece before positioning the Slim Cutter suction cups.
recommended to reduce the risk of the shifting of the
guide during cutting.
be distributed evenly along the central section of the
guide. This ensures that the profile is in contact with
the work piece at all times. (Fig. K)
the guide rail of the profile as shown in the image and
turn it 90° to prevent it from coming out.
Lock the position of the suction cup by tightening the
screw with the T-handle hex spanner (included, turn
clockwise). (Fig. L)
it to the work surface, pressing the handle as shown in
the image.
NOTE: position the suction cup at a recommended
angle of 0-20º. (Fig. LL)
Installation of SLIM CUTTER guides
follow the steps indicated in images. (Fig. M, N, O, P)
Securing the cutter to the SLIM CUTTER guide profile
guide as shown in the image (there is only one
possible position). (Fig. Q)
cutter and the guide, or that it is difficult to slide, you
will need to adjust the set of wheels.
WARNING! Do not use the cutter if the PRCD
protection indicator does not light up. It may be
damaged and should be replaced.
the voltage and frequency specified on the machine's
characteristics tag.
240V. 110 V machines may be connected to 100V /
120V.
damaged or broken parts and immediately repair or
replace any that are found.
the wrong direction, stop the machine and correct the
blade installation.
between 115 and 125 mm.
NOTE: The cutter is equipped with a PRCD unit
installed directly on the power supply cord. Verify that
it is functioning correctly before cutting.
indicator light should light up.
out.
13.
Publicidad
