Remote Control; How To Install Batteries; Battery Precautions - iLO DTV2784 Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

1
2
–/
3
4
5
6
7
8
PICTURE
SIZE
1. POWER Button - Press to turn the TV on. Press again to
turn the TV off.
2. Direct Channel Selection Buttons (0-9) - Allow direct
access to any channel.
3. -/DISPLAY Button - When the TV is receiving an analog
signal pressing this button will display the current infor-
mation on-screen. When the TV is receiving a digital,
pressing this button once will display the digital informa-
tion on-screen; pressing it a second time will display the
analog information on-screen. To remove the display
from the screen, press this button again. This button is
also the "-" button used when selecting digital channels.
Before using the remote control, batteries must first be installed.

HOW TO INSTALL BATTERIES

1. Open the battery compartment cover.
2. Install two "AAA" batteries.
3. Replace the battery compartment cover.
4. SLEEP Button - To set the TV to turn off after a preset
amount of time, press the SLEEP button. The clock will
count up 10 minutes each time the button is pressed in
the order of 0h00m, 0h10m,...1h50m,2h00m After the sleep
time is programmed, the display will disappear then reappear
momentarily every ten minutes to remind you the sleep
timer function is operating. To confirm the sleep time setting,
press the SLEEP button once and the remaining time will
be momentarily displayed. To cancel sleep time, press the
SLEEP button repeatedly until the display turns to 0h00m.
5. VOL (VOLUME) + / - Buttons - Press the + button to
increase, or the - button to decrease the volume level.
Use to select the desired setting during the menu screen
9
operation.
6. MENU Button - Press to display the menu screen function.
10
7. EXIT Button - Press remove the menu screen.
8. TV/AV Button - Press this button to display SOURCE
11
SELECTION menu to select the video input source.
9. QUICK VIEW Button - This button allows you to go back
to the previous channel selected by pressing the
12
QUICK VIEW button. Press this button again to return to
the channel you were watching.
13
10. MUTE Button - To turn off the sound, press this button once.
The TV will be silenced and the symbol "MUTE" will appear
14
on the screen. The muting feature can be released by
15
pressing the MUTE button again or one of the VOL
16
+ or - buttons.
11. CH (CHANNEL)
change to a higher numbered channel set into memory.
Press the
nel set into memory.
Use to select the desired setting during the menu screen
operation.
12. ENTER Button - Press to enter or select information for
On-Screen operations while in the adjustment menu.
13. RESET Button - Press to reset the menu screen picture
and sound adjustments to their factory preset positions
while in the adjustment menu.
14. CLOSED CAPTION Button - Press this button to display
CLOSED CAPTION menu.
15. AUDIO SELECT Button - Press this button to display
AUDIO menu.
16. PICTURE SIZE Button - Press this button to change
the picture size.
Use two "AAA" size batteries. The batteries may last
approximately one year depending on how much the remote
control is used. For best performance, it is recommended
that batteries should be replaced on a yearly basis, or when
the remote operation becomes erratic. Do not mix old and
new batteries or different types.

BATTERY PRECAUTIONS

These precautions should be followed when using batteries
in this device:
• Use only the size and type of batteries specified.
• Be sure to follow the correct polarity when installing the
batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device.
• Do not mix different types of batteries together (e.g.
Alkaline and Carbon-zinc) or old batteries with fresh ones.
• If the device is not to be used for a long period of time,
remove the batteries to prevent damage or injury from
possible battery leakage.
• Do not try to recharge batteries not intended to be recharged;
they can overheat and rupture (follow battery manufacturer's
directions).

Remote control

/
Buttons - Press the
button to change to a lower numbered chan-
button to
7

Publicidad

Capítulos

Tabla de contenido

Solución de problemas

loading

Tabla de contenido