Publicidad
Idiomas disponibles
Idiomas disponibles
How to Mow
Always use the correct mowing position (L1).
1.
2.
Start mowing from the outside edge of the lawn,
mowing in strips in alternate directions (L2).
3.
Mow twice a week in the growing season, your
lawn will suffer if more that one third of its
length is cut at one time and this may also
result in poor collection.
Please Note:-
Do not overload your Lawnmower
When mowing in long thick grass a first cut with the
cutting height adjusted to its highest setting, see
Cutting Height, will help reduce engine overload
and will help prevent damage to your lawnmower.
Cutting Height Adjustment
1.
The height of cut is altered by pulling the
adjustment lever away from the location slots
and moving to the selected position (L3).
Grass Collection Indicator
1.
Your lawnmower has a grass collection
indicator which tells you when the grassbox
needs emptying. (L4)
2.
When the indicator is at the top of the tube,
grass is being collected.
IMPORTANT
Do not attempt any maintenance on your
lawnmower when the engine is hot.
Cleaning
IMPORTANT
Never use water for cleaning your lawnmower. Do
not clean with chemical, including petrol, or solvents
- some can destroy critical plastic parts.
1. Remove grass from under the deck with a brush
(M1 and M2).
2. Using a soft brush - remove grass clippings from
the engine air intakes and exhaust (M3), cutting
height adjustment area. (M4), around the wheels
(M5) and the grassbox (M6 & M7).
3. Wipe over the surface of your lawnmower with a
dry cloth.
Cutting System
Removing the Blade
N1 or N2 BBC Only
•
Disconnect the spark plug lead.
1. Use spanner to loosen blade bolt by turning anti-
clockwise.
2. Remove the blade bolt, blade and spacer
washer.
3. Inspect for damage and clean as necessary.
Fitting the Blade
N1 or N2 BBC Only
1. Fit the blade to the machine with the sharp
edges pointing away from the machine.
2. Re-assemble blade bolt through blade and
spacer washer.
3. Hold firmly and tighten blade bolt firmly with a
spanner. Do not over tighten.
Please note: If you have a machine fitted with BBC
then you must remove both blade bolts with a
hexagonal drive key.
Use - Mowing
3.
When the indicator starts to drop, it's time to
empty the grassbox. Adopt a stationary position,
keeping the lawnmower running for 10 seconds.
Release the OPC lever or BBC arm and
remove the grassbox for emptying.(L5)
Emptying the Grassbox
Release the latch on the grassbox. (L6)
1.
2.
Release collection bag from grassbox frame.
(L7)
Empty grassbox. (L8)
3.
Using as a mulcher
1.
Your lawnmower is supplied with a mulching
plug. (L9)
Stop your lawnmower as described in Use -
2.
starting and stopping, and disconnect the
spark plug.
3.
Lift safety flap. Twist and slide mulching plug
into rear discharge chute. (L10)
Ensure mulching plug is securely fitted. (L11)
4.
5.
The mulching plug prevents grass from being
collected by blocking the collection chute on the
underside of the deck. (L12)
6.
Ensure the safety flap is positioned correctly.
(L13)
Maintenance
Always handle the blade with care - sharp edges
could cause injury.
USE GLOVES.
Renew your metal blade after 50 hours mowing
or 2 years whichever is the sooner - regardless
of condition.
If the blade is cracked or damaged replace it
with a new one.
How to Charge the Battery (50SE ONLY)
P1 - Wiring Loom
P2 - Charging Point
P3 - Cap
1. Stop your lawnmower.
2. Disconnect the spark plug.
3. Remove the cap from the charging point at the
bottom of the wiring loom (P).
4. Plug charger lead into connection on battery
loom
5. Plug the battery charger into a domestic electric
socket.
6. Charging will then commence.
7. Charge for 24 hours.
8. After charging, disconnect the charger from the
socket and charging point.
9. Replace the cap on the charging point.
10. The unit is now ready for use.
ENGLISH - 4
Publicidad
