Publicidad
Installation Instructions – Junction Box Interface (Connection at Ceiling) Pendant Pipe Mounting PP-_-JB
IMPORTANT SAFETY INFORMATION - READ, FOLLOW, AND SAVE ALL SAFETY AND INSTALLATION
INSTRUCTIONS.
Before starting any work ensure that all sources of power are turned OFF . All w ork must meet local/national electrical
●●
codes and be performed by a certified electrician.
Follow product label information and instructions before installing fixture. Retain installation instructions for fut ure
●●
reference.
Risk of fire, electrical shock, cuts and or other casualty hazards. This product must be inst alled in accordance with the
●●
applicable installation code by a person familiar with the constr uction and operation of the product and the hazards
involved. Cooper Lighting Solutions assumes no responsibility for claims brought about by impr oper or careless
installation or handling of this product.
Risk of burn. Disconnect power and allow fixture to cool before changing bulb or handling fixture.
●●
Replace lamp only with correct wattage and type of lamp marked on label. DO NOT exceed the maximum watt age listed
●●
on the fixture label.
To prevent wiring damage or abrasion, do not expose wiring to edges of sheet metal or any sharp objects.
●●
If supply wires are located within 3 inches of driver/ballast, use wire rated for at least 90°C (194°F).
Notee: Not all option available. Please consult your Cooper Lighting Solutions representative for availability.
Specification and dimension subject to change without notice.
2
Installation Instructions – Junction Box Interface (Connection at Ceiling) Pendant Pipe Mounting PP-_-JB
ADE141891 www.cooperlighting.com
WARNING
NOTICE
Installation Instructions – Junction Box Interface (Connection at Ceiling) Pendant Pipe Mounting PP-_-JB
INSTALLATION
Mount Details
4" Octagonal
Box to Structure
(By Others)
1/4 IPS Nut
Pendant Wire
(By Others)
1/2" Pendant
Figure 1.
Power
Connection at Ceiling
1.
Layout mounting locations.
2.
Ensure that power feed is at the UL end of the fixture.
Power feed: to be installed to local/national electrical
codes by a Certified Electrician.
3.
Secure junction boxes to structure.
4.
Secure crossbar to junction box.
5.
Attach pendant to crossbar using 1/4" IPS lock nut.
(Figure 1.)
6.
Feed wires through pendant to allow access in junction
box and connect wires ensuring all connections are
properly matched.
7 .
Slide canopy up pendant and tighten set screw.
N
otee:
Nominal ID for 1/4 IPS = 9.5 mm, 0.375 in.
N
otee:
Power wires can run through any pendant. (Refer to
local/national electrical codes).
Contact Corelite for connecting power at a joint for
N
otee:
Navigator II.
Crossbar
5'' Canopy
W/Slip Ring
Figure 2.
Non-Power
Installation Instructions – Junction Box Interface (Connection at Ceiling) Pendant Pipe Mounting PP-_-JB
ADE141891
Figure 3.
Power (2-D)
Figure 4.
Non-Power (2-D)
Mounts Locations
Distances are Equal to Fixture Length Plus or
Minus Dimensions Below
Fixture Family
DIM "A"
DIM "B"
DIM "C"
Class A
- 1 1/8"
- 1 1/8"
0"
Radius
- 1 1/8"
- 1 1/8"
0"
Iridum
- 1 1/8"
- 1 1/8"
0"
Stellar
- 2 3/8"
- 2 3/8"
0"
RZL
- 2 3/8"
- 2 3/8"
0"
Minigator
- 1 1/8"
- 1 1/8"
0"
Navigator II
+ 5/8"
- 5/16"
0"
Single Fixture
DIM "A"
Sample Row
DIM "B"
DIM "C"
DIM "D"
*For continuous rows see joining sheet
Figure 5.
Mounts Locations
www.cooperlighting.com
DIM "D"
0"
0"
0"
0"
0"
0"
+ 15/16"
3
Publicidad
