Functions Of Leds A And B; Adapter Insert (Ibox 01); Bluetooth; Bluetooth Usb Adapter - Bosch KTS 530 Descripción Del Producto

en 22 | ��S ��� � ��S ��� � ��S ��� | Description of unit
�.�.�

Functions of LEDs A and B

Status LED A
KTS ready for Does not illuminate
operation
Data commu- Flashes green
nication with (irregular)
the controller
Firmware update Does not illuminate
in operation
LED A Function
Does not il- No data com-
luminate munication with
the controller
Flashes green Data communication
(irregular) with the controller
Illuminated green Fault in hardware/
Firmware
Illuminated red Power sup-
ply > 35 Volt.
LED B Function
Does not il- Voltage not present
luminate
Flashes green KTS ready for
(1 second in- operation
terval)
Illuminated green Fault in hardware/
Firmware
Flashes yellow Overvoltage on
(1 second in- diagnostic cable
terval)
Illuminated yellow Fault in hardware/
Firmware
Flashes red Firmware update
(irregular) in operation
Illuminated red Fault in firmware-
update
Unplug the USB connection and power supply and connect them
*)
again. If the error still exists, contact customer service.
�.�.� Adapter insert (IBOX �1)
The adapter insert (Fig. 3, Item 8) contains all of the
existing capabilities for establishing communication
with the vehicle diagnosis interfaces that are known. In
order to flexibly adapt to future expansions in diagnosis
protocols, the adapter insert can be changed quickly
without any tools.
i
KTS modules only function with the adapter insert
connected.
|
1 689 979 987 2008-07-02
�.6
�.6.1
LED B
The Bluetooth USB adapter, which is included with
Flashes green
delivery, allows wireless connection with KTS 540 and
(1 second interval)
KTS 570. It is connected to the PC/Laptop and shows that
Flashes green
it is ready for operation when the red LED is illuminated.
(1 second interval)
!
Flashes red
It is
(irregular)
hardware installed or plugged into the PC/laptop, as
the data communication between the KTS module and
Measures the control unit would be disrupted as a result.
Check connection
!
with the controller
Do not put any mechanical stress on the Bluetooth
USB adapter and do not use it for gripping. This can
None
damage the laptop or Bluetooth USB adapter.
*)
�.6.2
Check volta-
ge in vehicle
Bluetooth Manager symbol
control unit diagnosis function is active:
Measures
Color
Check power
supply
Green
None
White
*)
White/green in
7-sec. cycle.
*)
Red
*)
Bosch Bluetooth Device symbol
the control unit diagnosis function is active:
None
Repeat firmware
Color
update
Green
Red
Symbol not
there.
i
Interrupting the Bluetooth connection with the
KTS 540 and KTS 570 can activate an acoustic alarm
signal in the PC/Laptop (see Online Help DDC). If a
fault occurs, the USB connection can be activated
and used instead of the Bluetooth connection.

Bluetooth

Bluetooth USB adapter

not possible to operate another piece of bluetooth

Information regarding Bluetooth symbols

(in toolbar) when the
Function
Bluetooth USB adapter active and com-
municating with KTS 540 or KTS 570.
Bluetooth USB adapter plugged into PC/lap-
top, but Bluetooth connection inactive.
Bluetooth USB adapter tries to create a wi-
reless connection to the KTS module.
Bluetooth USB adapter not
plugged into PC/laptop.
Function
Field strength of Bluetooth wireless link OK.
Field strength of Bluetooth wireless link too
low. Reduce distance between
Bluetooth USB adapter and the KTS
module or avoid obstacles such as
e. g. steel doors or concrete walls.
No Bluetooth wireless connection.
Follow the instructions in chapter 3.8.
(in toolbar) when
Robert Bosch GmbH