Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Equipment Required:
Fastener Kit: K36292
Wrenches: 13mm, 7/8
Drill Bits: None
1 1 1 1
Qty. (2)
Carriage Bolt, 1/2"-13 x 1-3/4"
2 2 2 2
Qty. (2)
Spacer, 1/4" x 1-1/2" x 2"
3 3 3 3
Qty. (2)
Lock Washer, 1/2"
1.
Lower vehicle exhaust.
2.
Remove three (3) existing bumper mounting bolts from each side and return to vehicle owner.
3.
Insert hitch between bumper bracket and frame rail. Install supplied M8 fasteners as shown above.
4.
Use pull wires to feed the carriage bolts and blocks into frame rails though access holes as shown.
5.
Install remaining fasteners as shown above.
6.
Raise vehicle exhaust.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2006, 2015 Cequent Towing Products – Printed in Mexico
Installation Instructions
CHEVROLET MONTE CARLO
Fascia
(Sold separately)
Drawbar Kit:
36061
Drawbar must be used in the
RISE position only.
Access Hole
Frame Rail
Exhaust Hanger
Tighten all M8 CL9.8 fasteners with torque wrench to 25 Lb.-Ft (34 N-m).
Tighten all 1/2 GR5 fasteners with torque wrench to 75 Lb.-Ft (102 N-m).
Do Not Exceed Lower of Towing Vehicle
Manufacturer's Rating or
3500 LB Max Gross Trailer Weight
300 LB Max Tongue Weight
Wiring Access Location: PC3, PC4
4 4 4 4
Qty. (2)
Hex Nut, 1/2"
5 5 5 5
Qty. (6)
Bolt with Conical Washer, M8 x 1.25 x 55mm
6 6 6 6
Qty. (2)
Pull Wire, 1/2"
Sheet 1 of 3
N36292
Part Numbers:
36292
06358
90150
Bumper Bracket
10-22-15
Rev. C
Publicidad
Manuales relacionados para Cequent Towing Products 36292
Resumen de contenidos para Cequent Towing Products 36292
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N36292 10-22-15 Rev. C 2006, 2015 Cequent Towing Products – Printed in Mexico...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 N36292 10-22-15 Rev. C 2006, 2015 Cequent Towing Products - Imprimé au Mexique...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684 Hoja 3 de 3 N36292 10-22-15 Rev. C 2006, 2015 Cequent Towing Products - Impreso en México...