Cequent Towing Products 24835 Instrucciones De Instalación

Hitch Shown In Proper Position
Equipment Required: Torque wrench
Fastener Kit: 24835F
Wrenches: 9/16 socket, ¾ socket, 6" extension
Drill Bits: None
Access Hole
1
2
3
4
1 1 1 1 Qty. (1) Carriage Bolt ½-13 x 1.75 GR5
2 2 2 2 Qty. (1) Spacer 1/4" x 1 x 3
3 3 3 3
Qty. (1) Conical Toothed Washer ½"
4 4 4 4 Qty. (1) Hex Nut ½-13
5 5 5 5 Qty. (1) Pull wire, 1/2
1. Lower exhaust by removing bolt in rubber hanger. Bend heat shield slightly to allow clearance for hitch side bracket.
2. Using the pull wire provided, install carriage bolt and spacer into frame rail (driver's side) through the access hole and into
the rearmost hole in the bottom of the frame rail. See figure 3.
3. Install U-bolts into the rear angled section of the frame as shown. See figure 2.
4. Raise hitch into position, being careful not to push the fasteners into the frame.
5. Install the conical toothed washer, ½ hex nut onto carriage bolt.
6. Install 3/8 flat washers, lock washers, and hex nuts onto u-bolts as shown.
7. Tighten all fasteners to specified torque below.
8. Re-install the exhaust lowered in step one.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z 2009, 2015 Cequent Towing Products – Printed in Mexico
Installation Instructions
Mitsubishi Galant
Fascia
(Sold separately)
Drawbar Kit:
3593
Drawbar must be used in the
RISE position only.
Heat Shield
Angle Plate In Frame
Vehicle Frame
6 7
8 9
Tighten all ½-13 GR5 fasteners with torque wrench to 75 Lb.-Ft. (102 N*M)
Tighten all 3/8-16 GR5 fasteners with torque wrench to 30 Lb.-Ft. (41 N*M)
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg.) Max Gross Trailer Weight
200 LB (90.8 Kg.) Max Tongue Weight
Wiring Access Location: TBD
Figure 1.
6 6 6 6 Qty. (2) U-Bolt, 3/8-16 x 1.06 GR5
7 7 7 7 Qty. (4) Flat Washer, 3/8-16
8 8 8 8
Qty. (4) Lock Washer, 3/8
9 9 9 9 Qty. (4) Hex Nut, 3/8-16
Sheet 1 of 3 24835N
Part Numbers:
24835
77209
60237
Manufacturer's Rating or
Bend Heat Shield to clear bracket
U-BOLT INSTALLATION
Insert one end of U-bolt into frame and
rotate into position through frame
Figure 2.
5
Figure 3.
10-8-15 Rev. C
Form F206 Rev A 5605