Technical Specifications - Master GEO Manual De Uso Y Mantenimiento

USER MANUAL
tubular motor Ø45 mm and ø35 mm with electronic limit switch
Dear customer, thank you for purchasing a MASTER product. This manual describe the operations for a correct installation of the product. This device is not design for a continuative
use. Use of the product other than that provided for in this manual is improper and prohibited and will void the warranty and any manufacturer's liability. The installation of the product
must be done by a qualified technician. At the end of the installation, all manuals must be given to the end user. Keep this manual for future reference!
To facilitate, improve and speed up any request to the assistance service it is necessary to provide the product name to the operator.
Before installing the motor, it is recommended to copy the technical data (including the extended product name) and store them in a safe place
PRODUCT INFORMATION
This motor has been designed to drive the main types of roll-up shutter. The motor is equipped with systems for recognizing possible obstacles
during the ascent phase. If the roll-up shutter is equipped with stop systems (mechanical stop (or cassette) or anti-lifting device (see section '03
MOUNTING NOTES ')), during the installation the product is able to automatically detect and memorize the limit switches. Moreover, the
presence of these devices will allow the motor to independently recover any deviations from the limit switches due to adjustment of the roll-up
shutter or other possible error factors. It is therefore recommended to always install the roll-up shutter with such devices (or at least one of the
two). You must use quality anti-lifting devices, able to withstand motor thrust for short periods. The number of anti-lifting devices to be used
depends on the weight of the roller shutter and the nominal torque of the motor.
If you proceed with the installation in the absence of anti-lifting devices and stopper (or cassette), it may occasionally be necessary to adjust the
limit switches (see sections 07 and 08).
If the roll-up shutter is not installed properly, the motor may detect non-existent obstacles during the up or down movements. In this case it is
necessary to verify the installation.

01. TECHNICAL SPECIFICATIONS

The technical characteristics of the motor are shown in the label applied to the motor tube. The common characteristics of the motor family are:
Power supply
GEO ø35 Min roller diameter
SIDE ø45 Min roller diameter
02. WARNINGS
02.1 Warnings for safety
Incorrect installation can cause serious injuries
programming and maintenance operations must be carried out only by a qualified and skilled technician, who must comply with laws, provisions, local regulations and the instructions
given in this manual ● The wiring must comply with current IEC standards. The final electrical system must be created only by the electrician
operation and can exclude the use of radio controls or require particular safety devices
shutter/awning regularly
02.2 Warnings for installation
Before installing the product, check the compatibility with the associated devices and accessories
knock and the use of unsuitable tools can cause the damage of the external or internal parts of the motor
parts without the manufacturer's permission
cable ● Any screws needed to complete the installation must not come into contact with the motor
shown on the motor) ● Some stages of programming and/or normal operation make use of the mechanical stops of the roller shutter/awning. It is essential to choose a motor with the
most suitable torque for the application, considering the actual traction of the roller shutter/awning, and to avoid motors that are too powerful
1mm thick ● Leave 1-2 mm of right/left play on the winding roller
supports and sundry accessories related to the motor must be chosen exclusively from the MASTER catalogue
or from another support surface, the moving parts must be protected with a cover to prevent accidental access. In any case, ensure access for maintenance work
must be positioned in such a way that it does not come into contact with moving parts
the cable in a protective tube ● Position the buttons within sight of the roller shutter/awning but a long way from its moving parts. Position the buttons more than 1.5 m from the floor
The motors are designed for residential use; the maximum continuous operating time is 4 minutes
contains a self-resetting thermal cut-out, which stops the motor if it overheats. The motor returns to normal operation when its temperature drops below the safety limit (normally after 5
to 10 minutes) ● The motor must be installed so that it cannot come into contact with liquids and in any case in a position protected from atmospheric agents
work near the winding roller while the motor is powered
automatically recalibrate the limit switches recovering slight deviations due to adjustment of the roller or a continuous and sudden power loss.
02.3 Warnings for use
The product is not intended to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they are
supervised or given instructions about the product way of use by a person responsible for their safety
distance, until the movement ends
being carried out (e.g. window cleaning, etc.). If the control device is automatic, disconnect the motor from the power line
03. MOUNTING NOTES
STOPPER
Make sure that the upper stop is
made of a stable reference
R
Information for any assistance requests
: 230 Vac 50 Hz IP insulation
: 50 x 1.5 mm Insulation class
: 40 x 1.5 mm
● Keep these instructions for future maintenance work and disposal of the product
● Do not carry the motor by the power cable. The product may not be used if the power cable is damaged. Do not try to replace the power
● Check that the shape and size of the drive pulley and adapter crown correspond to the winding roller used. Adapters,
● Where possible program the upper limit of the motor by contact with an obstacle. This solution will allow the motor to
● Do not allow children to play with the appliance or with the fixed control devices
OK
Make sure that the strap is in tension in
the lower end position
GEO - SIDE
: IP44
: H
● To prevent potentially dangerous situations, check the operating condition of the roller
● Check that the package is intact and has not been damaged in transit
● Do not pierce or tamper with the motor in any way. Do not modify or replace
● The power of the motor must be sufficient for the applied load (check the rated data
● If the product is installed at a height of less than 2.5 m from the floor
● The power cable of the product is suitable for indoor installation only. If installed outside, place
● During operation, the motor body becomes very hot, so be careful
● Check the automation during the movement and keep people at a safe
●
STRAP
OK
01
Continuos operating time
● All the product installation, connection,
● Some applications require hold-to-run
● Use winding rollers that are at least
●
Do not operate the blind when maintanance operations are
ANTI-LIFTING DEVICE
Make sure that the anti-lifting device is
mounted and fixed correctly and that the last
splint stays inside the guides
rev00 08.03.2018
: 4 minutes
● A heavy
● The power cable
●
● The motor
For your safety, do not
OK