Klipsch ProMedia 2.1 Manual Del Usuario página 3

adjusted separately from the Windows volume control. Consult applicable
manual for specific hardware documentation.
Subwoofer Level
For CD or DVD output, the optimum position will be indicated by the mark at 10
o'clock on the sub level control. Optimum sub levels and user preference may
vary from game to game. Usually a high bass level is preferred, especially at
low listening levels. Remember to reset the control settings before playing CDs
or films on DVD.
cOntrOL POD featUreS
Headphones: The 1/8" stereo headphone output jack, located on the
right-hand side of the control pod, turns off the two satellite speakers and the
subwoofer output. The main volume control will adjust the headphone output.
MP3/Aux: The MP3/Auxiliary input jack is used with portable audio players.
This signal will be mixed with the main source. The input has a +6dB input
sensitivity to help compensate for the lower output voltage of some portable
players. To obtain the proper balance with the main signal, the level adjust-
ments in the computer software and in the portable player will need to be
adjusted. An example would be listening to an MP3 player while surfing the net
and hearing associated sounds from various websites. The mixed sound may
not be desirable, and you will ultimately determine how you use this feature.
NOTE: During playback of MP3s, overall sound quality may be perceptibly
degraded compared to other audio sources such as CD. This is caused by the
encoding method and quality of the MP3 file. It is recommended that MP3 files
be encoded at a minimum 128 bit rate.
SPecIfIcatIOnS
(Visit www.klipsch.com for more details)
Satellite Impedance:
Preamplifier Control Pod:
Satellite:
Subwoofer:
Amplifier:
Subwoofer Limiter:
acceSSOrIeS
All accessories are available at www.klipsch.com.
WB-1 Wall Mount Brackets
Versatile Wall Bracket 1 is made from high quality steel. The clean, simple
design affords the most extreme angle adjustment, with up to 160 degrees of
4 ohms minimum
Subwoofer and Main volume level controls
LED power indicator
MP3/Aux player line input with soundcard
mixing function
Headphone jack
Direct path interface
Sealed elliptical two-way enclosure with
25mm metalized polymer dome tweeter
mated to MicroTractrixTM Horn and
3" long-throw mid-bass driver
Bass-reflex enclosure with rear port and
front-firing 8" long-throw driver; slot
tuned port; sixth-order enclosure design
High-efficiency power supply and linear
amplifiers designed for uncompressed full
power sound
Protective limiter function protects the
driver and amplifier from extremely high
volume playback
movement for precise speaker positioning in the horizontal plane. Wall stud
wood screws included.
trOUbLeSHOOtIng
If no sound, ensure that:
- Power, input, speaker cables connectors and AC power cord are securely attached
- Soundcard software is properly installed and functioning
- Computer sound (control panel) volume is turned up and not muted
- LED glowing
- Headphones are not connected
If one or more speakers have little or no sound, ensure that:
- All cables are connected properly
- Connectors are fully "seated" in soundcard and speakers
- Main and subwoofer level controls are properly adjusted on control pod
- Computer software audio settings are adjusted for proper use
- Computer system's sound (control panel) volume is turned up
If the satellites or subwoofer exhibit distortion or buzzing:
- Turn down computer's volume (via control panel), and reduce control pod volume
- Turn down subwoofer's volume, as program signal may be too strong
- Plug the subwoofer's power cord into a surge protector
If there is noise or hissing and the volume is low even when the main volume is up:
- Turn up computer's sound volume (via control panel)
- Turn down main volume on control pod to compensate
- Ensure that software/hardware is properly installed and operating
If there is computer monitor interference:
- Make sure the sub is positioned at least 3 feet (1m) from the computer monitor
- Increase the distance between the satellite speakers and the computer monitor
For more detailed information and FAQs, please visit www.klipsch.com.
FCC EMC Statements
Approved under the verification provision of FCC Part 15 as a Class B Digital Device.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of
the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- CAUTION: Changes or modifications not expressly approved by
manufacturer could void the user's authority to operate this device.
Specifications are subject to change without notice.