Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Pontiac Bonneville – All Models, Buick LeSabre – All Models
Frame Rail
Fascia
Hitch Shown In Proper Position
Equipment Required: Tin Snips
Fastener Kit: F36309
Wrenches: 15mm, 17mm, 9/16, 3/4
Drill Bits: ½"
Heat shield
Mounting bolt
To be removed
And discarded
Figure 2
Heat shield trim
Passenger Side
Shown
1
Qty. (2)
Bolt Assembly M10 x 1.50 x 45mm CL9.8
2
Qty. (2)
Carriage Bolt ½-13 x 1.75 GR5
3
Qty. (2)
Block ¼ x 1 x 3
4
Qty. (2)
Lock Washer ½"
1.
Remove exhaust hanger bracket from bottom of frame rail and disconnect from rubber hanger attached to exhaust tail pipe. A
replacement bracket is provided and will be installed later. Return factory exhaust brackets to vehicle owner.
2.
Raise hitch into position. Using hitch as a template, drill (2) ½" holes.
Note: On vehicles equipped with heat shield, remove rearmost fastener which secures heat shield to frame rail and discard.
Trim heat shield as shown in Figure 2.
3.
Lower hitch and fishwire carriage bolts and blocks as shown in Figure 1.
4.
Raise hitch into position and install remaining fasteners as shown in Figure 1. Heat shield, if present, will be sandwiched
between frame and hitch side bracket at installation.
5.
Attach hanger brackets. Install 3/8-16 x 2" carriage bolt thru square hole in bracket to bottom of frame. Slide rubber hanger
onto 3/8" carriage bolt and secure with flanged locknut. Tighten nut against rubber hanger allowing hanger to rotate – DO NOT
OVER TIGHTEN.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to
prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety precautions when working
beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5
and SAE J684.
z
2005 Cequent Towing Products
Installation Instructions
Buick Lucerne – All Models, Oldsmobile Aurora
Drawbar Kit:
Drawbar must be used in the
Rise position only.
Trim heat shield
Around drilled
hole
Heat
Shield
Drilled Hole
5432
Tighten all M10 CL9.8 fasteners with torque wrench to 53 Lb.-Ft.
Tighten all 3/8 GR5 fasteners with torque wrench to 31 Lb.-Ft.
Tighten all 1/2 GR5 fasteners with torque wrench to 75 Lb.-Ft.
36063
Do Not Exceed Lower of Towing Vehicle
3500 LB Max Gross Trailer Weight
300 LB Max Tongue Weight
Wiring Access Location: PC3, PC4
Frame Rail
Weldnut
1
5
Qty. (2)
6
Qty. (2)
7
Qty. (2)
8
Qty. (2)
Sheet 1 of 3
Manufacturer's Rating or
76
1
On vehicles with
Dual exhaust, hanger
Bracket arrangement
Figure 1
Typical both sides
Hex Nut ½-13
Carriage Bolt 3/8-16 x 2" GR5
Flanged Locknut 3/8-16
Exhaust Hanger Bracket
N36309
11-22-05
Part Numbers:
36309
06976
90140
2345
Rubber
Hanger
8
Rev. B
Form F206 Rev A 5605
Publicidad
Manuales relacionados para Cequent Towing Products 36309
Resumen de contenidos para Cequent Towing Products 36309
- Página 1 This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. Sheet 1 of 3 N36309 11-22-05 Rev. B 2005 Cequent Towing Products Form F206 Rev A 5605...
- Página 2 Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. Feuille 2 de 3 N36309 11-22-05 Rev. B 2005 Cequent Towing Products Form F206 Rev A 5605...
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York. V.E.S.C. Regulación V-5 y SAE J684. Hoja 3 de 3 N36309 11-22-05 Rev. B 2005 Cequent Towing Products Form F206 Rev A 5605...