Leviton RS Serie Instrucciones De Instalación

RS Series
LED Floodlight Fixtures
Cat. Nos. RS111, RS121, RS151, RS161, RS211, RS221, RS251, RS261, RSPOL
INSTALLATION INSTRUCTIONS
IMPORTANT! READ BEFORE INSTALLING FIXTURE
WARNINGS & CAUTIONS
• TO AVOID FIRE, SHOCK, OR DEATH: TURN OFF POWER at circuit breaker or fuse and test that
power is off before wiring or servicing fixture!
• TO AVOID FIRE, SHOCK, OR DEATH: this product MUST BE connected to a wiring system with
an equipment grounding conductor.
• TO AVOID ELECTROSTATIC DISCHARGE: clean lens surface with damp cloth only.
• This product should be installed, inspected, and maintained by an electrician, in accordance with
all applicable electrical codes.
• Read these instructions before installation and retain for future reference.
• The equipment is required to be installed with metallic conduit or armored cable to facilitate external
equipotential bonding.
• For connections use wire rated to a minimum of 95˚C.
© 2015 Leviton Mfg. Co., Inc.
FOR CANADA ONLY
For warranty information and/or product returns, residents of Canada should contact Leviton in writing at Leviton
Manufacturing of Canada Ltd to the attention of the Quality Assurance Department, 165 Hymus Blvd, Pointe-
Claire (Quebec), Canada H9R 1E9 or by telephone at 1 800 405-5320.
LIMITED 5 YEAR WARRANTY AND EXCLUSIONS
Leviton warrants to the original consumer purchaser and not for the benefit of anyone else that this product at the
time of its sale by Leviton is free of defects in materials and workmanship under normal and proper use for five
years from the purchase date. Leviton's only obligation is to correct such defects by repair or replacement, at its
option. For details visit www.leviton.com or call 1-800-824-3005. This warranty excludes and there is disclaimed
liability for labor for removal of this product or reinstallation. This warranty is void if this product is installed improperly
or in an improper environment, overloaded, misused, opened, abused, or altered in any manner, or is not used
under normal operating conditions or not in accordance with any labels or instructions. There are no other or
implied warranties of any kind, including merchantability and fitness for a particular purpose, but if any
implied warranty is required by the applicable jurisdiction, the duration of any such implied warranty, including
merchantability and fitness for a particular purpose, is limited to five years. Leviton is not liable for incidental,
indirect, special, or consequential damages, including without limitation, damage to, or loss of use of,
any equipment, lost sales or profits or delay or failure to perform this warranty obligation. The remedies
provided herein are the exclusive remedies under this warranty, whether based on contract, tort or otherwise.
For Technical Assistance Call: 1-800-824-3005 (U.S.A. Only) www.leviton.com
© 2015 Leviton Mfg. Co., Inc.
APPLICATION
The RS Series LED fixtures are designed for use indoors, outdoors, wet locations, and areas containing moisture,
dirt, corrosion, vibration, and rough usage. They are suitable for use in the following areas as defined by the
National Electrical Code (NEC ® ) and the Canadian Electrical Code (CEC
cCSAus:
Class I, Division 2, Groups ABCD; Class II,
Division 1 and 2, Groups EFG; Class III; T4;
Canada: Zone 2, Ex nA IIC, T4; Zone 20;
USA: Class I, Zone 2, AEx nA IIC, T4; Zone 20:
IECEx:
Group II: Ex nA IIC T4 or 133.5˚C Gc
Group III: Ex tb IIIC T95˚C Db
SPECIFICATIONS
VOLTAGE 90-277 VAC | 130-420 VDC | 347-477 VAC - See unit label
INPUT 2.3 A @ 120 VAC | 1 A @ 277 VAC | 0.8 A @ 347 VAC
3/4" NPT Conduit
CONNECTIONS
HOUSING Copper-free Aluminium Cast, Aluminium & Polycarbonate lens
MOUNTING Wall - 2-6x 3/8" Bolts (not provided). Use suitable length screws for mounting application.
Pole - Tenon Bracket (not provided)
TEMPERATURE -40˚C to +50˚C
INGRESS PROTECTION IP65
INSTALLATION
WARNING: TO AVOID FIRE, SHOCK, OR DEATH: TURN OFF POWER at circuit breaker or fuse and test that
power is off before wiring or servicing fixture!
Step 1: (Wall & Pole Mount): Remove Wall Bracket
[A] from the Power Supply Box [B] (Fig. 1).
FIG. 1
[B]
[A]
Wall Mount - Proceed to Step 3A
PK-A3082-10-02-0A
PK-A3082-10-02-0A
® ):
Step 2: (Wall & Pole Mount): Assemble the Power
Supply Box [B] to Head [C] (Fig. 2) in desired
configuration (see Configurations).
FIG. 2
[C]
M6
M5
M6
M5
M6
M6
M6
Pole Mount - Proceed to Step 3B
150˚ 150˚
Step 3A: (Wall Mount): Mount Wall Bracket in desired
location. Ensure a minimum of two (2) 3/8" bolts (not
provided) are used to secure the fixture to the wall
surface. One in each of the upper [X] and lower [Y]
hole clusters (Fig. 3A). NOTE: It is recommended
to use four (4) bolts in high wind and vibration
environments.
5.9"
[150 mm]
Wall Mount - Proceed to Step 4A
Step 4A: (Wall Mount): Slide assembled fixture [D]
onto Wall Bracket [A].
Step 5: (Wall Mount): Align and mount the lower four
(4) M6 bolts first [E] then proceed with the top four (4)
M6 bolts [F] (Fig. 4A).
[D]
CONNECTIONS
Step 7: (Wall & Pole Mount): Open the Power
Supply Box lid (Fig. 7).
DIAGRAMS
NOTE: For connections use wire rated to a minimum of 95˚C.
Model: 90-277 VAC | 130-420 VDC
Brown: +
Blue: -
Green: Earth
(Factory)
Line IN Ground to be terminated
on Grounding Post of the Power Supply Box.
Model: 347 VAC
Black: Line
M6
White: Neutral
[B]
Green: Earth
(Factory)
Line IN Ground to be terminated
on Grounding Post of Power Supply Box.
CONFIGURATIONS / CONFIGURACIONES
150˚
150˚
150˚
150˚ 150˚
150˚
Wall Mount
Step 3B: (Pole Mount): Position tenon bracket (not
provided) onto pole and secure in place with three (3) 3/8"
hex bolts (Fig. 3B).
FIG. 3A FIG. 3B
1.5"
[38 mm]
[X]
4.3"
[111 mm]
[Y]
Pole Mount - Proceed to Step 4B
Step 4B: (Pole Mount): Position fixture onto pole mount
tenon bracket and secure in place with four (4) M6 bolts
(Fig. 4B).
Pole Mount - Proceed to Step 6.
FIG. 4A FIG. 4B
[F]
[A]
Step 6: (Wall & Pole Mount): Adjust Head angle if
[E] required. NOTE: Adjustable in 15 degree increments.
Step 8: (Wall & Pole Mount): Connect the desired
Conduit/Wire runs to the desired 3/4" NPT entry and run
wire as per applicable standards for area of use.
Step 9: (Wall & Pole Mount): Connect the AC IN feed to
labeled wires in the Power Supply Box as per applicable
FIG. 7 standards for area of use (see Diagrams).
Step 10: (Wall & Pole Mount): Close the Power Supply
Box lid. Torque lid screws according to Fig. 8.
FIG. 8
POWER SUPPLY BOX
Green/Ground (Factory)
Power Supply 1
POWER SUPPLY BOX
Power Supply 2
Green/Ground (Factory)
Pole Mount
8 6
4 2
70 in·lbf
10 9
1 3
7 5
Blue Black
HEAD
Red White
Blue Black
Red
White
HEAD
Orange
Blue 347 PS1 & PS2 joined
in factory. Connect to
Red Red
provided splicing
connectors.