Publicidad
Idiomas disponibles
Idiomas disponibles
1. SETUP
1
Fill base unit with
250ml/9floz water
2. USAGE
1
To turn on the unit - hold down
the power button for 2 seconds,
the LED will flash red and beep
once to show that the unit is in
standby mode
6
Close the lid
3. CLEANING & DESCALING
CLEANING
After each use, unplug and allow to cool before
cleaning. Pour away any excess water and wipe with
a damp cloth only. Do not clean with abrasive
cleaners or allow to come in to contact with solvents
or harsh chemicals, damage could result.
DESCALING
We recommend carrying out the descaling process
approximately every 4-weeks. If you notice limescale
earlier than 4-weeks, descaling may be required
sooner. Living in a hard water area can produce
limescale quicker than other areas. You can find out
your water quality via your water provider. You may
need to repeat either process if you find that
limescale is still present. Alternatively, you may wish
to use a specific descaling solution suitable for
electric warmers if your build up is significant, you
may need to use a stronger solution.
Please refer to instructions leaflet before use and remember to clean and descale your unit regularly
2
If heating a pouch, insert pouch
holder - bottles can be placed
directly in to the base of the
unit
For your childs safety always check food temperature before feeding by testing on a sensitive part of the skin
2
Select temperature - press until
the green LED is adjacent to
your requirement
7
Press the power button - LED
will turn solid red and beep once
to show the cycle has started
There are two methods of descaling that you can follow for your warmer.
Option 1:
1. Empty the electric warmer and wipe down the inside with a clean sponge or damp cloth.
2. Pour in 1 cup of white vinegar.
3. Leave for at least 30 minutes, or up to 24-hours depending on the extent of the limescale.
4. Pour any remaining liquid down the sink. Rinse the interior of the warmer well with cool water and use a clean sponge or damp
cloth to remove any build up that came loose as a result of the descaling/cleaning process.
5. Plug unit back in and add regular amounts of water you use for normal warming. Turn on and run for 5 minutes to remove any
additional build up. Upon completion, rinse warmer again and use as directed.
Option 2:
1. Empty the electric warmer and wipe down the inside with a clean sponge or damp cloth.
2. Pour in 1 cup of white vinegar.
3. Turn on the warmer and run for a cycle, approximately 5-minutes.
4. Unplug the unit and leave to cool, then pour any remaining liquid down the sink. Rinse the interior of the warmer well, with cold
water and use a clean or damp cloth to remove any build up that came loose as a result of the descaling/cleaning process.
5. Plug unit back in and add regular amounts of water you use for normal warming. Turn on and run for 5 minutes to remove any
additional build up. Upon completion, rinse warmer again and use as directed.
3
Plug unit in to mains power
supply and place the unit on a
clean, dry kitchen work surface
3
Select pouch or bottle type -
press until the green LED is
adjacent to your requirement
8
When cycle finishes the unit
will beep 3 times and red light
will start to flash. Unit will
automatically turn off when
cycle is complete and reset
The descaling process will remove deposits of calcium and other
minerals in the system that may affect its performance
4
Hold down the power button
for 2 seconds to turn on the
unit. The LED will flash red and
beep once to show the the unit
is in standby mode
4
Select volume of feed - press
until the green LED is adjacent
to your requirement
9
Open lid and remove feed
taking
care not to touch the water
inside the unit as it will have
heated during the cycle.
Empty
unit and replace water after
every use to ensure it holds the
correct amount
5
The unit is now ready to use
5
Insert feed - we recommend using
the pouch holder to suppport all
milk storage pouches, Bottles can
be placed directly in to the base
of the unit. For hygiene we
recommend leaving the hood on
the teat
RESET
To cancel a cycle - hold down
the power button and the
temperature selection button for
5 seconds and unit will reset
Publicidad
