Declaration Of Conformity; Manufacturer's Warranty; Technical Specifications - STEINEL PROFESSIONAL HF 3360 KNX Información

EU countries only:
Under the current European Directive on Waste Electrical and Electronic Equipment
and its implementation in national law, electrical and electronic equipment no longer
suitable for use must be collected separately and recycled in an environmentally
compatible manner.
10� Declaration of Conformity
Hereby, STEINEL Vertrieb GmbH declares that the radio equipment type HF 3360
KNX is in compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address: www.steinel.de
11� Manufacturer's Warranty
As purchaser, you are entitled to your statutory rights against the vendor. If these
rights exist in your country, they are neither curtailed nor restricted by our Warranty
Declaration. We guarantee that your STEINEL Professional sensor product will remain
in perfect condition and proper working order for a period of 5 years. We guarantee
that this product is free from material-, manufacturing- and design flaws. In addition,
we guarantee that all electronic components and cables function in the proper man-
ner and that all materials used and their surfaces are without defects.
Making Claims
If you wish to make a claim, please send your product complete and carriage paid
with the original receipt of purchase, which must show the date of purchase and
product designation, either to your retailer or contact us at STEINEL (UK) Limited,
25 Manasty Road, Axis Park, Orton Southgate, Peterborough, PE2 6UP, for a re-
turns number. For this reason, we recommend that you keep your receipt of purchase
in a safe place until the warranty period expires. STEINEL shall assume no liability for
the costs or risks involved in returning a product.
For information on making claims under the terms of the warranty, please go to
www�steinel-professional�de/garantie
If you have a warranty claim or would like to ask any question regarding your product,
you are welcome to call us at any time on our Service Hotline 01733 366700.
5
Y E A R
MANUFACTURER'S
WARRANTY
22
12� Troubleshooting
Malfunction Cause
No power at the sensor
n Break in wiring
Sensor will not switch ON n Bulb faulty
n Twilight setting set to
night-time mode during
daytime operation
Sensor will not switch OFF
n Continuous movement
in the detection zone
Sensor keeps switching n Curtains, plant etc.
ON/OFF
moving in the sensor's
detection zone causing
the sensor to respond
Sensor responds when it
n Sensor near Wi-Fi or
should not other wireless commu-
nication sources
13� Technical specifications
Dimensions (H × W × D) Surface-mounted installation, round Ø
Surface-mounted installation, square
Concealed installation, round Ø
Concealed installation, square
Application inside buildings
Power supply KNX bus voltage, 21 V - 30 V
Sensor system 5.8 GHz high frequency
Mounting height 2 - 2.8 m
Transmitter power approx. 1 mW
Settings via ETS software, remote control or BUS
Angle of coverage 360° with 180° angle of aperture
Basic brightness 1 - 255 min
Twilight setting 2 - 1000 lux, teach
Light output Switching / dimming / basic brightness
Light 1 – Light 2
Lighting stay-ON time 1 - 255 min
HVAC stay-ON time 1 - 255 min
HVAC switch-ON delay Room surveillance, 1 - 255 min
Further outputs In-operation telegram
IP rating Surface-mounted: IP54
Temperature range -20°C to +50°C
Remedy
n Check KNX power
supply
n Change bulb
n Adjust setting
n Check zone
n Check zone
n install at least 2 m away
from the wireless com-
munication source
126 × 52 mm
95 × 95 × 52 mm
124 × 64 mm
94 × 94 × 64 mm
(SELV)
Concealed: IP20
23