Fuel Cell Safety Warning; Warning For Tools With Contact Actuation Capability - CELO FOX Instrucciones De Seguridad Y Funcionamiento

English
• Please keep the tool in clean condition, wipe off grease
or oil after work. Do not use any solvent based cleaner to
clean the tool. It is possible the solvent will deteriorate
the rubber or plastic components on the tool. Greasy
handle and body will cause accidental drop of the tool
and injury to nearby person.
• Recommended fasteners and accessories
- Use only fasteners made or recommended by the tool
manufacturer, or fasteners that perform equivalently to those
recommended by the manufacturer.
- Use only accessories made or recommended by the tool
manufacturer, or accessories that perform equivalently to
those recommended by the manufacturer.
Remarks: Accessories included, Battery, Battery Charger and
Fasteners. Please refer to the technical data sheet for their
specifications.
• Do not use the tool to perform other job than designate
function. Especially not use the tool as a hammer, impact
on the tool will increase the risk of cracked body and
accidental discharge of fastener.
• Load the fastener at last to prevent unexpected fastener
firing when loading fuel cell and battery.
• Operating controls
- Do not use a tool with missing or damaged safety warning
label(s.)
- A tool that is not in proper working order must not be used.
Tags and physical segregation shall be used for control.
- Do not remove, tamper with, or otherwise cause tool opera-
ting controls to become inoperable.
- Do not operate tool if any portion of the tool operating
controls is inoperable, disconnected, altered, or not working
properly.
• Tool handling
- Only persons who have read and understand the tool opera-
ting/safety instructions should operate the tool.
- Always assume that tool contains fasteners.
- Do not point tool toward yourself or anyone whether it con-
tains fasteners or not.
- Keep bystanders and children away while operating tool.
- Do not actuate tool unless tool is placed firmly against the
workpiece.
- Respect tool as a working implement.
- Do not engage in horseplay.
- Stay alert, focus on your work and use common sense when
working with tools.
- Do not use tool while tired, after having consumed drugs or
alcohol, or while under the influence of medication.
- Do not overreach. Keep proper footing and balance at all
times.
- Do not hold or carry tool with a finger on the trigger.
- Drive fasteners into proper work surface only.
- Do not drive fasteners into other fasteners.
- After driving a fastener, tool may spring back ("recoil") cau-
sing it to move away from the work surface. To reduce risk of
injury always manage recoil by:
- always maintaining control of tool.
- allowing recoil to move tool away from work surface.
20
- not resisting recoil such that tool will be forced back into
the work surface. In "Contact Actuation Mode" if workpie-
ce contact is allowed to re-contact work surface before the
trigger is released, an unintended discharge of a fastener will
occur.
- keeping face and body parts away from tool.
- When working close to an edge of a workpiece or at steep
angles use care to minimize chipping, splitting or splintering,
or free flight or ricochet of fasteners, which may cause injury.
- Keep hands and body away from fastener discharge area of
tool.
- Do not load tool with fasteners when any one of the opera-
ting controls is activated.
- Do not operate tool with any power source other than that
specified in tool operating/safety instructions.
- Do not operate tool with any operating pressure other than
that specified in tool operating/safety instructions.
- Always select an actuation system that is appropriate to the
fastener application and the training of the operator.
- Use extra caution when driving fasteners into existing walls
or other blind areas to prevent contact with hidden objects or
persons on other side (e.g., wires, pipes.)
• Remove the fuel cell and battery when
- Not in use;
- Performing any maintenance or repairs;
- Clearing a jam;
- Elevating, lowering or otherwise moving the tool to a new
location;
- Tool is outside of the operator's supervision or control; or
- Removing fasteners from the magazine.

Fuel cell safety warning

• Use only the fuel cell recommended by the manufacturer.
Read the Material Safety Data Sheet to understand more
of your fuel cell contents.
• Recycle the empty fuel cell according to the local law.
Do not attempt to recharge the fuel cell or incinerate the
empty fuel cell.
• Do not expose the fuel cell or tools loaded with fuel cell
under direct sun light exposure. Prevent to put above
items at temperature higher than 120°F(50°C). Overhea-
ting the fuel cell can result in explosion or fire.
• Do not puncture or attempt to open the fuel cell. The fuel
cell contains flammable gas even if it appears empty.
• The content of the fuel cell is extremely flammable, keep
it away from all source of ignition.
Remarks : Recommended fuel cell – PREGUN Item#165
mm 40g 80ml or the equivalent.
WARNING for tools with
contact actuation capability
• Do not rest your finger on the trigger when picking up the
tool, moving between operating areas and positions or
walking, as resting finger on trigger can lead to inadver-
tent operation. For tools with selective actuation, always
check the tool before use to ascertain the correct mode is