Sime MURELLE 25 OF Manual Del Usuario página 93

3.3 ACCESS TO INSTALLER'S
PARAMETERS
For access to the installer's parameters,
press simultaneously the keys
for 5 seconds (3 fig. 14).
For example, the parameter PAR 23 is
visualised on the display of the control
panel in the following way:
The paramet er s scr oll for war ds and
backwards with the key and
the default parameters can be changed
with the keys and .
The standard visualisation returns automa-
tically after 60 seconds, or by pressing one
of the control keys (2 fig. 14).
3.3. 1 Replacing the board or
RESETTING parameters
If the electronic board is replaced or reset,
it is necessary to configure PAR 1 and PAR
2 by associating the following values to
each type of boiler to be able to restart the
boiler:
BOILER GAS MODELS
METHANE 20
25
30
BF/BFT 35
LPG 20
25
30
35
METHANE 25
OF/OFT 30
LPG 25
30
BOILER
OF/BF
OF/BF COMBINED
WITH SUN-PANEL SYSTEM
OFT - BFT - 25/55 - 30/55
SYSTEM
AQUAQUICK
NOTE: the inside of the upper door of the
boiler panel has a label with the values
that have to be set for PAR 1 and PAR 2
(fig. 21).
FAST CONFIGURATION
PAR DESCRIPTION
and
1 Combustion configuration
2 Hydraulic configuration
3 Timetable 2 programmer
4 Pressure transducer disabler
5 Assignment of auxiliary relay AUX
(D.H.W. tank)
6 Luminous bar indicating presence
of voltage
and
7 Allocation of CR 73 channels
8 --
9 --
10 Remote control option setting
11 Correction values external sensor
D.H.W. - HEATING
PAR DESCRIPTION
20 D.H.W. minimum temperature
21 D.H.W. maximum temperature
22 Anti-legionella (D.H.W. tank)
PAR 1
23 Boiler antifreeze
1
24 External sensor antifreeze
25 Climatic curve setting Zone 1
2
26 Climatic curve setting Zone 2
3
27 Minimum temperature Zone 1
4
28 Minimum temperature Zone 2
5
29 Minimum temperature Zone 2
6
30 Maximum temperature Zone 2
31 Maximum heating power
7
32 Post-circulation temperature
8
33 Pump activation delay Zone 1
9
34 Re-ignition delay
10
11
12
EXPANSION CHART
PAR DESCRIPTION
PAR 2
40 Assignment to mixed zones
1
41 Mix valve stroke time
2
42 Priority D.H.W. over mixed zone
43 Floor drying
3
4
5
RE-SET
PAR DESCRIPTION
49 Reset default parameters
(par. 01-par 02 = "-")
PARAMETERS INSTALLER
RANGE UNIT OF
MEASUREMENT
-- = ND
1 ... 12
-- = ND
1 ... 5
1 = DHW + Recirc. pump
2 = DHW
3 = Recirculation pump
0 = Disabled
1 = Enabled
1 = Remote supply
2 = Recirculation pump
0 = Disabled
1 = Enabled
0 = Not assigned
1 = Circuit 1
2 = Circuits 1 and 2
--
--
1 = CR 73
2 = CR 53
3 = RVS
-5 ... +5
RANGE UNIT OF
MEASUREMENT
10 °C ... PAR 21
PAR 20 ... PAR 62 OEM
0 = Disabled
1 = Enabled
- 5 ... +5
- 15 ... +5
3 ... 40
3 ... 40
PAR 64 OEM ... PAR 28
PAR 27 ... PAR 65 OEM
PAR 64 OEM ... PAR 30
PAR 29 ... PAR 65 OEM
30 ... 100
0 ... 199
0 ... 199
0 ... 10
RANGE UNIT OF
MEASUREMENT
1 = Zone 1
2 = Zone 2
0 ... 199
0 = Paralle
1 = Absolute
0 = No activated
1 = Curve A
2 = Curve B
3 = Curve A+B
RANGE UNIT OF
MEASUREMENT
-- , 1
INC/DEC DEFAULT
UNIT SETTING
= = "--"
= = "--"
= = 1
= = 1
= = 1
= = 1
= = 1
-- -- --
-- -- --
= = 1
°C 1 0
INC/DEC DEFAULT
UNIT SETTING
°C 1 30
°C 1 60
= = 0
°C 1 3
°C 1 - 2
= 1 20
= 1 20
°C 1 20
°C 1 80
°C 1 20
°C 1 80
% 1 100
Sec. 10 30
10 sec. 1 1
Min. 1 3
INC/DEC DEFAULT
UNIT SETTING
= = 1
10 sec. 1 12
= = 1
= = 0
INC/DEC DEFAULT
UNIT SETTING
= = =
ES
PT
GB
93