Vestil SB-48 Manual Del Propietário

VESTIL MANUFACTURING CORPORATION
2999 North Wayne St., Angola, IN 46703
Ph: 260-665-7586 Fax: 260-665-1339
www.vestil.com • sales@vestil.com
Ergonomic Solutions
Contents
Hardware Kits .............................................................. 1
Receiving Instructions ................................................. 1
Warranty ...................................................................... 1
CONCRETE HARDWARE KIT
The following tools/hardware are required for installing your
speed bump.
SB-48-CK KIT INCLUDES:
3 - 1/2" x 6" lag bolt for each hole
3 - 1/2" washers for each lag bolt
3 - 1/2" anchor sleeve for each bolt
SB-36-CK KIT INCLUDES:
4 - 1/2" x 6" lag bolt for each hole
4 - 1/2" washers for each lag bolt
4 - 1/2" anchor sleeve for each bolt
SB-108-CK KIT INCLUDES:
5 - 1/2" x 6" lag bolt for each hole
5 - 1/2" washers for each lag bolt
5 - 1/2" anchor sleeve for each bolt
CUSTOMER SUPPLIES:
1 - High-speed hammer drill 3/4" masonry bit
1 - Impact wrench or heavy ratchet 3/4" socket
ASPHALT HARDWARE KIT
The following tools/hardware are required for installing your
speed bump.
SB-48-AK KIT INCLUDES:
3 - 12" long steel spikes
2 - pieces of Butyl tape
SB-36-AK KIT INCLUDES:
4 - 12" long steel spikes
2 - pieces of Butyl tape
SB-108-AK KIT INCLUDES:
5 - 12" long steel spikes
2 - pieces of Butyl tape
CUSTOMER SUPPLIES:
1 - Sledge Hammer
RECEIVING INSTRUCTIONS
Every unit is thoroughly tested and inspected prior to
shipment. However, it is possible that the unit may incur
damage during transit. If damage is noticed when unloading,
make a note of it on the BILL OF LADING. Remove all packing
and strapping material, then inspect the unit again for damage.
IF DAMAGE IS EVIDENT, FILE A CLAIM WITH THE CARRIER
IMMEDIATELY!
WARRANTY
This product is warranted for 30 DAYS from date of
purchase to be free of manufacturing defects in material and
workmanship. The manufacturer's obligation hereunder is lim-
(standard)
Revised 07-10
A company dedicated to solving ergonomic and material
handling problems since 1955 .
OWNERS
MANUAL
SPEED BUMP MODEL SB-36, 48, & 108
MODEL SBA-36, 48 & 108
Assembly Instructions ................................................... 1
Assembly Drawing ........................................................ 1
Material Handling Problem Solvers ............................... 4
ited to repairing such products during the warranty period,
provided the product is sent prepaid back to the factory.
This warranty does not cover normal wear of parts or
damage resulting from any of the following: negligent use or
misuse of the product, use or application contrary to installation
instructions, or disassembly, repair or alteration by any person
prior to authorization from a factory representative.
ASSEMBLY INSTRUCTIONS
CONCRETE (standard)
1.) Position the speed bump in its intended position and using
its predrilled holes as templates, mark the location of each
hole on the road surface.
2.) Remove the speed bump. Using high speed hammer drill
with a 3/4" masonry bit, drill a hole at each marked location
to a depth of 3-1/2" below the road surface.
3.) Insert a anchor sleeve into each hole (large sleeve opening
on top). Tap the sleeves into the holes with a hammer so
thatthe sleeves are set flush with the surface. Place a
washer over each sleeve hole.
4.) Make sure the substrates are thoroughly clean and dry.
Reposition the speed bump in its installation position. Apply
firm hand pressure. Slip a washer onto a lag bolt, insert the
bolt through a predrilled hole in the speed bump, align over
anchor sleeve and tighten the bolt about three-quarter of
the way with the 3/4" socket. Repeat for each hole in the
speed bump. Finish tightening each bolt until just snug.
DO NOT OVER TIGHTEN! Excessive tightening may dam
age the speed bump and void the product warranty.
ASSEMBLY INSTRUCTIONS
ASPHALT, HIGH USE AREA'S, OR LOCATIONS WITH TEM-
PERATURES OVER 110°F
1) Adhere the Butyle tape to the under structure of speed
bump length wise.
2) Place speed bump in desired position.
3) Insert spike through pre-drilled hole. DO NOT HOLD
SPIKE WHILE HAMMERING! Drive spike into ground until
flush with speed bump.
SPEED BUMP
MODEL SB-48, 36, 108
MODEL SBA-48, 36, 108
29-126-102
E
N
G
L
I
S
H
E
S
P
A
N
O
L
F
R
A
N
Ç
A
I
S