Safety Notes; Operating Conditions; Technical Data - Grohe 36 414 Manual De Instrucciones

GB

Safety notes

Prevent danger resulting from damaged voltage
supply cables. If damaged, the voltage supply cable
must be replaced by the manufacturer or his customer
service department or an equally qualified person.
• Before and during use make sure that the thermostat is
functioning correctly. Children and adults with reduced
sensory capabilities should not use the product
unsupervised.
• When the domestic water system is drained, the thermostats
must be drained separately since non-return valves are
installed in the hot and cold water connections. For this
purpose, the mixer must be removed from the wall.
• Installation is only possible in frost-free rooms.
• The switched-mode power supply is only suitable for indoor
use.
• The plug-in connectors must not be directly or indirectly
sprayed with water when cleaning.
• The voltage supply must be separately switchable.
• Use only genuine replacement parts and accessories.
The use of other parts will result in voiding of the warranty
and the CE identification, and could lead to injuries.
Application
Infrared fittings with thermostat are designed for hot water
supply via pressurised storage heaters and, utilised in this
way, provide the best temperature accuracy. With sufficient
power output (from 18 kW or 250 kcal/min), electric or gas
instantaneous heaters are also suitable.
All thermostats are adjusted in the factory at a flow pressure
of 0.3 MPa on both sides.
Should temperature deviations occur on account of special
installation conditions, the thermostat must be adapted to local
conditions (see "Adjusting").

Operating conditions

®
Bluetooth version 4.0. The current version of the
app required for using the system must be installed on
the control unit in advance.
The required App is available for free in the iTunes Store
(requires an Apple account) and the Google Play store
(requires a Google account), see fold-out page IV.
For operation under adverse environments, in buildings /
rooms with reinforced concrete walls, steel and iron frame, or
near of obstructions (eg furniture) of metal, the Bluetooth
reception can be disturbed and interrupted.
Type of obstructions Interference or shielding
potential
Wood, Synthetic Low
material
Water, Bricks, Marble Medium
Plaster, concrete, High
glass, solid wood
Metal Very high
The transceiver operates in the ISM-frequency range
(2.4GHz). The installation in the vicinity of equipment with the
same channel occupancy should be avoided.
In cases of malfunktions, turn off the source of interference
shortly.
3

Technical data

36 332 000, 36 333 000:
• Voltage supply:
36 414 000:
• Voltage supply: 100-240 V AC 50-60 Hz/6.75 V DC
• Power consumption:
®
Bluetooth :
• Power consumption:
• Output:
®
• Bluetooth - version:
® -
• Bluetooth Transmission distance:
(depending on the environments)
• Minimum flow rate:
• Automatic safety shut-off:
• Run-on time:
• Reception range according to Kodak Gray Card,
grey side, 8x10", landscape
- Start / stop water flow:
- Automatically stop water flow:
• Type of fitting protection:
Hot water temperature at supply connection min. 2 °C
higher than mixed water temperature.
Thermal disinfection possible.
Electrical test data
• Software class
• Contamination class
• Rated surge voltage
• Temperature of ball impact test
The test for electromagnetic compatibility (interference emission
test) was performed at the rated voltage and rated current.
If static pressures exceed 0.5 MPa, a pressure-reducing valve
must be installed.
Installation
, see fold-out page I and II.
Flush pipes thoroughly before and after
installation (observe EN 806)!
Open hot and cold water supply and check that
connections are watertight.
Reversed connection (hot on right - cold on left)
Replace thermostatic compact cartridge, see Replacement
Parts, fold-out page II,Prod. no. 47 175 (1/2").
When using this thermostatic cartridge, the Cool Touch
function is no longer available.
Electrical installation
Electrical installation work must only be
performed by a qualified electrician. This work
must be carried out in accordance with the
regulations to IEC 60364-7-701 (corresponding to
VDE 0100 Part 701) as well as all national and local
regulations.
Only water-resistant round cables with max. outside
diameter of 6.0 to 8.5 mm may be used.
Adjusting
Setting temperature see fold-out page II.
6V lithium battery type CR-P2
4 W
1 W
®
Bluetooth - Class 2
4.0
about 10m
5 l/min
60 s
1 s
5cm
40cm
IP 59K
A
2
2500 V
100 °C
, see fold-out page II.