Publicidad
Idiomas disponibles
Idiomas disponibles
M54506 - EXP. CARD μSD memory
This is a descriptive manual of the procedure to insert and
configure the inputs/outputs expansion card (relay) of the
CVMk2.
You can download the complete manual in digital format
from www.circutor.com
Before any maintenance, modification to the
connections, repair, etc., the equipment must
be disconnected from the supply and the
measure connections. If wrong operation is
suspected the equipment must remain out of service. The
equipment is designed to changed quickly in the event
of any breakdown.
1. CARD INSTALLATION
Disconnect from supply and measure the device.
Remove the screw and the cover
Insert the card in the guides.
Press the card carefully.
Put the cover and the screw.
2. CARD SELECTION
When we have introduced the card, we have to configure it.
MENU
Select
from the upper line of the display and confirm
SET
with
to unfold the window.
SETUP
SET
Select
and confirm with
move in the upper menu with the arrows since
SET
and select it with
key.
CARD 1
CARD 2
We have 3 options (
,
to select according the position which we have introduced
the card. In the picture is position 1, then we will select
CARD 1
.
NOTE: If select you select a position where is no card, will
appear the message
NO CARD
.
When we have selected the card we have to confirm with
the
SET
key and will enter in the configuration.
The memory card has to be FAT16 and maximum
capacity of 2 Gb.
Not insert FAT32 and HCSD formats.
3. FORMAT
To erase the registry files or do a memory format, we have
to unfold the window
SET
key.
We have to move in the upper menu with the arrows since
EXP.CARD
the
We have 3 options (
have to select according the position which we have
introduced the card. In the picture is position 1, then we
will select
The keys of this screen are:
esc
: Go back, window without saving changes.
ok
: Leave the editing window saving the changes.
It creates a single file of events *. EVQ which holds
all voltage events. The files *. STD, are generated
automatically every day.
In the format screen, where we can see the following
settings.
Clear STD
•
Clear evq
•
Format
•
: Do a memory format.
extract
•
4. PARAMETRES VISUALIZATION
To see the parameters of the microSD memory card, you
have to unfold the window menu and select exp.card.
Select card 1, card 2 or card 3 depending on the position
of the card and will see the parameters:
MEM.size
key. Now, we have to
•
EXP.CARD
•
recorded
•
events
: Voltage events detected since last memory
CARD 3
or
). We have
•
free
:
•
status
: Indicates the status of the microSD:
M54506 - Expansion card μSD memory -
A T E N T I O N : W h e n y o u i n s t a l l a n
m i c r o S D c a r d i n t h e C V M k 2 , i t ' l l b e
formatedautomatically. Don't insert memory
cards with documents that you want to keep.
menu
setup
, select
and confirm with
SET
and select it with the
key.
CARD 1
CARD 2
CARD 3
,
ó
CARD 1
.
: Erase the last record file.
: Erase the last voltage event detected.
: Stops the communications between device
and memory microSD.
AT T E N T I O N : B e f o r e t o e x t r a c t t h e
microSD memory from the device, we
have to stop the communications between
device and microSD card. If don't srops the
communications, the microSD memory card
could be damaged.
: microSD Capacity in Mb
: Recorded days since last memory format.
format
% of free memory
a)
SD.OK
: it is correct
b)
No SD
: No microSD detected
c)
WR PROTE
: The microSD has the wirte
protection enable
d)
SD error
: format microSD must done.
5. PARAMETRES SELECTION
The card is programmed to record 234 predefined
variables.
In the event that the user needs to modify the selection of
variables, must use Power Studio software found on the
web CIRCUTOR, www.circutor.com
After communicating with the computer using the software,
you have access to the driver of the device and therefore
access to the configuration of the card
) and we
The user must select the expansion card to be enabled the
following option:
A window in whith all the variables the device can register
appears and the user can select which want to register.
6. ICONS
Correct status of microSD memory.
Incorrect status of microSD memory.
microSD card extraction enable.
7. TECHNICAL ASSISTANCE SERVICE
In case of failure or any operational queries, please contact
the technical service of CIRCUTOR, SA.
TECNICAL ASSISTANCE SERVICE (TAS):
(+34) 93 745 29 00
CIRCUTOR, SA. – Aftersales service.
Vial Sant Jordi s/n
08232 Viladecavalls, Barcelona.
Tel.: (+34) 93 745 29 00
Fax: (+34) 93 745 29 14
e-mail: sat@circutor.es
CVM k 2
M98209301-20-15A
Publicidad
