Introduction; Features; Initial Setup; Connections And Controls - Phonic GEQ 1502F Manual Del Usuario

INTRODUCTION

congratulations on your purchase of another quality
product, We hope the GEQ1502F or GEQ3102F graphic
equalizer proves itself to be a worth investment, and
provides you with years of dependable use for many
years to come. These equalizers were meticulously
designed by skilled engineers, and should give you total
control of your audio's various frequencies. use the GEQ
equalizer in your speaker path, or use it with your mixer'
s insert points to integrate it better into your system.
We know how eager you are to get started, however we
advise that you take the time to read through this manual
before storing it in an easy to remember place for future
reference. Within this manual you'll find helpful information
on the operation and treatment of the GEQ unit.

FEATURES

● Ultra low-noise operation
● Professional 15-band stereo Graphic Equalizer for
live and studio application alike (GEQ1502F)
● Professional 31-band stereo Graphic Equalizer for
live and studio application alike (GEQ3102F)
● FB.D Feedback Detection circuitry instantly reveals
problem frequencies in your audio
● Low cut filter removes unwanted low-frequency
sounds
● High cut filter helps users better determine
frequencies they wish to work with (GEQ3102F)
● Dedicated subwoofer output with crossover control
● Accurate 4-digit output level meter (GEQ1502F)
● Accurate 6-digit output level meter (GEQ3102F)
● Gain control for adjusting input levels
● High quality workmanship and sturdy construction
● Balanced 1/4" TRS and XLR input and output
connectors

INITIAL SETUP

1. after opening and unpacking the GEQ equalizer,
inspect the unit for any noticeable damage. Though
attempts to take every precaution possible in
preventing damage occurring to its products in
transit, it is sometimes unavoidable. if the product is
noticeably damaged, users are advised to contact the
dealer at which they purchased the product.
2. if you wish to mount the GEQ into a 19" rack, ensure it
is not positioned above power amplifiers and that the
unit has plenty of ventilation, as to avoid overheating.
3. plug any required devices into the GEQ's inputs and
outputs. For example, a mixer's output signal could
be sent to the inputs, and an amplifier and speakers
connected to the outputs.
4. plug the provided power cord into the power connector
and into an appropriate ac power source. Be sure
to check local voltage levels before connecting the
unit. Do not under any circumstances defeat the
ground-pin of the cord, as it is provided for your own
protection.
GEQ1502F / GEQ3102F

CONNECTIONS AND CONTROLS

Front Panel

1.Output Level Meter
This 6-segment lED level meter (4-segment on the
GEQ1502F) will give you an accurate indication of when
the output level of the GEQ equalizer reaches certain
levels. if the red "clip" lED illuminates, users are advised
to reduce the level of that particular channel, either
through use of the input level control or by lowering the
frequency slide controls.
2. FB.D Switch
The FB.D Feedback Detection system is activated when
this button is pushed. When feedback is detected, an
lED will illuminate on the affected frequency's slide
control. users can lower the level of that frequency to
eliminate the feedback.
3. Audio In/Out Switch
pushing this button will enable and disable the equalizer
function for the respecting input channel. When the
equalizer is disabled, the input signal will be sent directly
to the output channel without being altered.
4. Range Switch
This switch is used to change the boost/cut range of
the frequency slide controls between ±12 dB and ±6 dB
(switch depressed).
5. Input Control
This control is used to adjust the input level for the
corresponding channel. it gives you a boost/cut range
between -15 and +15 dB.
6. Low Cut Switch/Control
The low-cut button on the GEQ1502F will remove
frequencies below 25 hz to help eliminate unwanted
stage rumble and other unpleasant low-frequency
sounds.
The GEQ3102F features a low-cut control that will allow
users to select the cut-off frequency of the low-cut filter
between 10 and 400 hz. please note that this affects the
signal sent through the subwoofer output, as well.
1 1
2 4
3
3 6
5
GEQ 1502F
2
4
5 6 7
GEQ 3102F
1