janitza RD 96 Manual De Instrucciones página 6

Ocultar thumbs Ver también para RD 96:

Manual del usuario (30 páginas)

Instrucciones de instalación (3 páginas)

Tabla de contenido

Idiomas disponibles

General

Disclaimer

Compliance with the usage information for the

WARNING

devices is a prerequisite for safe operation and

attaining the stated performance characteristics

Risk of injury due to electrical voltage!

Severe bodily injury or death can result from:

and product features. Janitza electronics GmbH

· Touching bare or stripped leads that are ener-

assumes no liability for bodily injury, material dam-

gized.

age or financial losses which result from disregard

· Device inputs that pose a hazard when touched.

of the usage information.

Switch off your installation before commenc-

ing work! Secure it against being switched on!

Check to be sure it is de-energized! Ground

Make sure that your usage information is readily

and short circuit! Cover or block off adjacent

available and legible.

live parts!

Additional documentation can be found on our

website at www.janitza.de under

Intended use

Support > Downloads.

The device is:

• Intended for installation in switchboard cabinets

and small installation distributors. The mount-

ing position is arbitrary (please note the step

"Mounting").

distribution or other use, in whole or in part, is

• Not intended for installation in vehicles! Use of

prohibited.

the device in non-stationary equipment consti-

tutes an exceptional environmental condition

Subject to technical changes.

and is only permissible by special agreement.

• Make sure that your device matches the instal-

• Not intended for installation in environments

lation instructions.

with harmful oils, acids, gases, vapors, dusts,

• First read and understand the documents asso-

radiation, etc.

ciated with the product.

• Is designed as a device for use indoors, protect-

ed from weather influences.

Mounting

Operation and button functions

Install the device in the weatherproof front panel of

switchboard cabinets.

After connecting the USB cable, the UMG 801 dis-

play screen appears on the external display (RD 96)

after a time delay.

Fig. Mounting orientation, rear view, RD 96

Cutout dimensions: 92

+0.8

x 92

+0.8

Cutout dimensions: 92

Fig. Standard display, UMG 801 - RD 96

+0.8

x 92

+0.8

(3.62

in x 3.62

in)

(3.62

+0.03

in x 3.62

+0.03

in)

+0.03

INFORMATION

To ensure ventilation of the device, take into ac-

Further information on the operation, display and

count the distances to adjacent components!

functions of your UMG 801 and the RD 96 can be

found in the respective user manual.

• Keep the documents associated with the prod-

uct available for the entire service life and pass

Incoming goods inspection

them on to any possible subsequent users.

The prerequisites for trouble-free and safe operation

• Please find out about device revisions and the

of this device include proper transport, storage,

associated amendments of the documentation

setup and assembly, as well as proper operation and

associated with your product at www.janitza.de.

maintenance. Exercise due caution when unpacking

and packing the device, do not use force and only

Disposal

use suitable tools. Check:

Please abide by national regulations! Dispose of

• Visually inspect the devices for flawless mechani-

individual parts, as applicable, depending on their

cal condition.

composition and existing country-specific regula-

• Check the scope of delivery (see user manual)

tions, e.g. as:

for completeness before you begin installing the

• Electronic waste

device.

• Plastics

• Metals

If it can be assumed that safe operation is no longer

or engage a certified disposal

possible, the device must be taken out of operation

company to handle scrapping.

immediately and secured against unintentional start-

up.

Relevant laws, standards and directive used

It can be assumed that safe operation is no longer

possible if the device, for example:

Please see the declaration of conformity on our

• has visible damage.

website (www.janitza.de) for the laws, standards

• No longer functions despite an intact power

and directives applied for the device by Janitza

supply.

electronics GmbH.

• was subjected to extended periods of unfavorable

conditions (e.g. storage outside of the permissi-

ble climate thresholds without adjustment to the

room climate, condensation, etc.) or transport

stress (e.g. falling from an elevated position, even

without visible external damage, etc.).

CAUTION

Pressing function button 1 ESC takes you to the

Material damage due to disregard of the

menu selection of the measurement device (a

mounting instructions.

detailed description can be found in the UMG 801

Disregard of the installation instructions can dam-

user manual).

age or destroy your device.

· Provide adequate air circulation in your

installation environment. For high ambient

temperatures, provide cooling if necessary.

Display for measured values

and device configuration

Display symbols of the

button functions

Function buttons

2 2

Safety

2 2

Safety

Brief device description

Safety information

The installation instructions do not represent a

The external RD 96 display:

compete set of all safety measures required for the

• is intended for the Janitza UMG 801 measure-

operation of the device.

ment device and for front panel installation;

Special operating conditions can require additional

• requires neither additional software nor drivers

measures. The installation instructions contain

and functions using plug & play via the USB

information which must be observed to ensure your

interface of the UMG 801;

personal safety and avoid material damage.

• has 6 function buttons for operation.

Symbols used on the device:

A USB cable is included in the scope of delivery

which is used to establish the connection be-

The additional symbol on the device

tween the external display and the UMG 801 using

itself indicates an electrical danger

plug&play.

that can result in serious injuries or

death.

The USB connection cable remains in the switch-

This general warning symbol draws

board cabinet or small distribution board and must

attention to a possible risk of injury.

be laid separately from other electrical circuits!

Be certain to observe all of the

Please note the special rules for the USB interface

information listed under this symbol

in step 5.

information listed under this symbol

in order to avoid possible injury or

even death.

Safety information in the installation instructions is

marked by a warning triangle and, in dependence

on the degree of hazard, is displayed as follows:

Secure the device inside the switchboard or on the

front panel using the fastening clips on the side. To

The RD 96 is operated using 6 buttons which, in accordance with the UMG 801, have the following func-

do so, proceed as follows:

tions:

• Before inserting the device, remove the fasten-

• Selecting measuring displays.

ing clips (e.g. with a screwdriver) by levering

• Navigation within the menus.

them horizontally.

• Device configuration.

Function buttons

Display symbols

RD 96

ESC

Fig. Side views of the RD 96 with fastening clips.



• Guide the device through the switchboard

(mounting plate) from the front.

• Attach the clips to the side of the device by

pushing them in and snapping them into place.

6 / 8

DANGER

INFORMATION

Indicates the immediate threat of danger that

leads to severe or fatal injury.

Further information about the RD 96 external

leads to severe or fatal injury.

display can be found in the user manual!

Further information on the functions, instal-

WARNING

lation, operation and technical data of the

UMG 801 can be found in the corresponding

Indicates a possibly hazardous situation that can

usage information!

lead to severe injury or death.

CAUTION

Warns of an immediately hazardous situation

which, if not avoided, can result in minor or mod-

erate injury.

ATTENTION

Warns of an immediately hazardous situation

which, if not avoided, can result in material or

environmental damage.

INFORMATION

Indicates procedures in which there is no hazard

of personal injury or material damage.

• Screw in the clamping screws until they touch

the mounting plate.

• Then tighten the clamping screws with two fur-

ther turns each. Too tightly tightened clamp-

ing screws can destroy the fastening clips!

Function

· Display menu.

· One step back.

Button 1

· Cancel action (ESC).

· Repeated actuation leads to the menu.

Mounting clip

· Select position (to the left, "3").

Button 2

· Select menu item or position

(up, "5").

Button 3

· Change selection (digit +1).

· Select menu item or position

(down, "6").

Button 4

· Change selection (digit -1).

· Select position (to the right "").

Button 5

INFORMATION

Once the clamping screws touch the mounting

· Confirm selection (Enter)

plate, turn them a max. of 2 further turns!

Button 6

Mounting

plate

Function buttons

UMG 801

Clamping

screw

Screwdriver

Tabla de Contenido

Tabla de contenido

Productos relacionados para janitza RD 96

janitza RCM Serie

janitza RD 96 Manual De Instrucciones página 6

Idiomas disponibles

Manuales relacionados para janitza RD 96

Productos relacionados para janitza RD 96

Tabla de contenido