Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
Hitch Shown In Proper Position
Fastener Kit: 24901F
Fastener Kit: 24901F
Wrenches: 11/16 , 17MM
Qty. (2)
Bolt M10 X 1.5 X 35
Qty. (4)
WASHER CONICAL 7/16
Qty. (1)
SQUARE U BOLT 7/16
1. Remove nuts holding the exhaust hanger to the end panel and pull hanger off studs and out of the way.
2. Route M10 bolts with conical washers though existing hole in both sides of end panel.
3. Mount hitch on the end panel studs and the bolt routed though the existing hole.
4. Reinstall the exhaust hanger and the bolts with hitch against the end panel and place M10 nuts on the bolts (.
5. Attach forward bar of hitch to vehicle cross member with the U bolt and secure with 7/16 conical washers and nuts provided.
6. After hitch is fully installed and in place tighten all fasteners to the torque specs listed below.
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body
panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged should be removed and replaced. Observe safety
precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch.
This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.
Regulation V-5 and SAE J684.
z
2012, Cequent Towing Products INC.
Installation Instructions
CADILLAC ATS
Fascia
Drawbar Kit:
3593
Drawbar must be used in the
Rise position only.
Existing
vehicle nut
Tighten all 7/16 8.8 fasteners with torque wrench to 58 Lb.-Ft. (102 N*M)
Tighten all 10MM GR5 fasteners with torque wrench to 38 Lb.-Ft. (102 N*M)
Do Not Exceed Lower of Towing Vehicle
2000 LB (908 Kg) Max Gross Trailer Weight
200 LB (90.8 Kg) Max Tongue Weight
Existing hole
in end panel.
Qty. (2)
Hex Nut M10 X 1.50
Qty. (2)
HEX NUT 7/16 -20
Sheet 1 of 2
N24698
Part Numbers:
24901
60334
77288
Manufacturer's Rating or
Wiring Access Location: PC3, PC4
11-9-12
Form F206 Rev A 5605
Vehicle cross
member
Rev. A
Publicidad
Manuales relacionados para Cequent Towing Products CADILLAC ATS
Resumen de contenidos para Cequent Towing Products CADILLAC ATS
- Página 1 Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684. 2012, Cequent Towing Products INC. Sheet 1 of 2 N24698 11-9-12 Rev.
- Página 2 Ne jamais utiliser une torche pour découper un accès ou un trou de fixation. Ce produit est conforme aux normes V-5 et SAE J684 de la V.E.S.C. (État de New York) concernant les spécifications en matière de sécurité des systèmes d’attelage. 2012, Cequent Towing Products INC. Feuille 1 de 2 N24698 11-9-12 Rev.
- Página 3 Este producto cumple con las especificaciones y requisitos de seguridad para conectar dispositivos y sistemas de remolque del estado de Nueva York, V.E.S.C. Regulación V-5 y SAE J684. 2012, Cequent Towing Products INC. Sheet 1 of 2 N24698 11-9-12 Rev.