Seat Assembly; Mounting The Rear Bumper; Side Discharge Chute Assembly (For Models With Side Discharge Only); Mounting The Cutting-Means Assembly - ST MPST 84 Li 48 V1 Manual Del Usuario

5.3 SEAT ASSEMBLY

Fit the seat (fig. 4.A) onto the plate (fig. 4.B) using
the screws (fig. 4.C).

5.4 MOUNTING THE REAR BUMPER

1a. For type "l" bumpers only - Mount the front
bumper (fig. 5.A) on the bottom of the frame
(fig. 5.B) using the four screws (fig. 5.C).
1b. For type "II" bumpers only
1. Fit the two brackets (fig. 5.A) and (fig. 5.B)
to the bottom of the frame (fig. 5.C)
following the direction of assembly
indicated in the figure: R= right; L= left.
2. fully tighten the screws (fig. 5.D).
3. Attach the front bumper (fig. 5.E) to the
brackets (fig. 5.A) and (fig. 5.B) using
the screws (fig. 5.F) and nuts (fig. 5.G).
5.5 SIDE DISCHARGE CHUTE
ASSEMBLY (FOR MODELS WITH
SIDE DISCHARGE ONLY)
1. From the inside of the side discharge
chute (fig. 6.A), fit the spring (fig. 6.B) by
inserting the terminal (fig. 6.B.1) into the
hole and turning it so that both the spring
(fig. 6.B) and the terminal (fig. 6.B.2) are
securely positioned in their seatings.
2. Position the side discharge chute (fig. 6.A)
in line with the cutting-means assembly
brackets (fig. 6.C). Using a screwdriver,
turn the second terminal (fig. 6.B.2)
of the spring (fig. 6.B) to bring it
outside the side discharge chute.
3. Fit the pin (fig. 6.D) in the holes on the
brackets (fig. 6.C) and on the side discharge
chute, so that it passes through the coils
of the spring (fig. 6.B) and the drilled end
comes out of the inner most bracket.
4. Insert the cotter pin (fig. 6.E) in the pin
(fig. 6.D) hole (fig. D.1) and rotate the pin
until it is possible to bend the two ends
(fig. 6.E.1) of the cotter pin, (with the aid
of a pair of pliers), so it cannot slide out
and cause the pin to fall out (fig. 6.D).
CAUTION
Check that the spring works correctly and keep
the side discharge chute securely lowered. Make
sure that the pin is fitted properly to prevent
it from falling out accidentally. Make sure that
the side discharge guard (fig. 7.A) is lowered
and locked by the safety lever (fig. 7.B).
WARNING
Before dismantling or servicing the
deflector, remember to push the safety
lever (fig. 8.B) and lift the side discharge
guard (fig. 8.A) to facilitate its removal.
NOTE
To dismantle the deflector, follow the
sequence in reverse order of assembly.
5.6 MOUNTING THE CUTTING-
MEANS ASSEMBLY SIDE
REINFORCEMENTS (FOR
SIDE DISCHARGE MODELS
ONLY, IF FORESEEN).
Complete the mounting of the cutting-means
assembly by fitting the side reinforcements
on the cutting-means assembly profile
using the screws supplied (fig. 9)
5.7 REAR PLATE ASSEMBLY AND
COMPLETION (FOR REAR
COLLECTION MODELS ONLY)
1. Assemble the two lower brackets
(fig. 10.A) and (fig. 10.B), following the
assembly direction as shown in the
illustration, and fasten them with the
screws (fig.10.C) and nuts (fig. 10.D),
tightening them completely.
2. Remove the two screws (fig. 10.H),
which will be used later.
3. Assemble the lower part (fig. 10.E)
of the rear plate and fasten it to
the lower brackets with the screws
(fig. 10.F) and bolts (fig. 10.G), without
tightening them completely.
4. Finish fastening the lower part (fig. 10.E)
of the rear plate, completely tightening
the two central screws (fig. 10.H)
that you previously removed and
the four upper screws (fig. 10.l)
5. Fully tighten the two bottom
nuts (fig. 10.G).
6. Insert the lever (fig. 10.J) of the
"grass catcher full" indicator into
its seat (fig. 10.K) and push it
down until you hear a click.
7. Assemble the two grass catcher brackets
(fig. 10.L) and (fig. 10.M), following the
assembly direction as shown in the
illustration, and fasten them with the
screws (fig. 10.N) and snap washers
(fig. 10.O), tightening them firmly.
EN - 10